My Timbertech XLM Mountain Cedar is turning white in some spots. I wanted to start a forum asking how many other people where having the same problem.
Timbertech got back with me and said to do the following:

• Step one:
Place 100% cotton towel in area from which surface is off color.

• Step two:
Set flat iron on a low steam setting

• Step three:
Keep flat iron moving on the towel in a back and forth motion

NOTE: Keep flat iron moving; do not let the iron set in one area because it may melt the deck.

• Step four:
Check area frequently to see results, continue until desired appearance is reached.

The issue is that I have not had any mats or anything in the areas that I am having the problem. Please respond if you are having the same problem. The other problem is that this technique is very time consuming and does not work well. I should not have to do this with an extreme low maintenance product.

I tried the link to the pictures but it didn't work. Could you email the link to me?

jkempf@orepac.com

I installed XLM Mountain Cedar in June or 2008 using 12', 16' and 20' foot boards. The 12's have turned to the color of a plastic milk jug in area's not protected by a chair or table and some of the 16's have started to turn white as well. I have pictures that show 2 boards at a butt joint with 1 side white and the other only slightly faded. I showed the pictures to the lumber yard where I ought the material and they were amazed. They are going to infomr ther supplier and show him the pictures but they also suffgested that I open a claim with Timbertech which i did 2 days ago. I was told that a warranty claim packaged would be sent to be. I'll try to keep this post updated as this process continues.

'cwgluch' could you email me pictures of your claim?

I had a Timbertech XLM (Mountain Cedar color) deck installed, about 8 months later I discovered large white areas, which can't be cleaned-up. Interestingly, the contractor ran out of XLM planks for the steps, so he bought one more. None of those planks (from a different production lot) are turning white, but the other ones, right next to the newer ones, are turning white. This must be a production lot issue with the XLM decking. I have contacted Timbertech to initiate a warrantee claim...we will see what happens.

I installed a Timbertech XLM Mountain Cedar deck in June '08 with hidden fasteners, and it looked great. After 9 months, the traffic areas turned white, and areas under tables or not walked on stayed brown. The white won't wash off. The deck gets VERY little traffic, and right now, it looks terrible. I would NOT buy that decking again. I'm waiting to hear from the Timbertech claims people (I just sent it off). This was supposed to be a maintenance-free material, but it isn't. Sorry I bought it.

See my pictures, and links to other posts:

http://www.rounsevell.com/timbertech/timbertech_20IMG_2328.jpg

http://www.rounsevell.com/timbertech/timbertech_20IMG_2329.jpg

http://stlouis.craigslist.org/mat/1317482822.html


http://www.topix.com/forum/autos/chevrolet-equinox/TQ0BMV7PUQPLSDQBG

My deck was installed last summer also, and when I spoke to the company about a settlement, he told me that the claim is being put through without a visit from Timbertech and as far as he knew they were going to "replace" the deck. My materials alone were around 13K and months of labor from my husband and myself. We did a meticulous job, each board was custom cut, and on difficult cuts, we made templates. I have many angles on my deck. I seriously doubt anyone would go to the trouble of what we went through.

Has anyone experienced these white-out problems with the "RiverRock", which is the gray XLM? I'm thinking of getting it and it sounds like all the problems are with 1 specific color?? Thanks.