Onion Domes
I have been trying to find out resources to help me build small onion dome say 1.5' dia at the bse and about same height. I have searched the inte...
I have been trying to find out resources to help me build small onion dome say 1.5' dia at the bse and about same height. I have searched the inte...
0
answers46
ViewsI recently inherited a Craftsman Belt Sander Model No. 315.11721, and I went to use it today but realized that the belt needed changed. Only one p...
55
answers2957
ViewsI have a springfield/duracraft wood lathe that a family member gave me and I'm trying to find a manual for it. Does anyone know where to go to fin...
0
answers108
ViewsI was recently given a Model 100 radial arm saw. It is missing several parts. I can buy many of them online at ***** but not a manual. I would be ...
19
answers1060
ViewsI would like to get a manual for a sander model 315-11640 or where I can go to get parts. Any help will be appreciated. Thanks.
0
answers94
ViewsI have a perfectly good small bandsaw, Black and Decker BS 700. The drive belt broke and it is discontinued and everywhere I have tried to find a b...
0
answers114
ViewsThere is a very thick vine which is going up the side of the house (cedar). I am trying to remove it because the moisture it traps can cause the w...
5
answers959
ViewsThe timing belt came off and ground into the housing. After removing the split ring/washer, I"m trying to remove the blower from the housing to re...
2
answers1231
ViewsI am in the market for a bench top mortiser. I have read a bunch of reviews but still looking for some advise. I will be mainly mortising in to a ...
0
answers106
ViewsI have a Skil Miter Saw model 3316. Does anyone know of a way to get a laser guide for it? The model doesn't offer it as an accessory, at the momen...
0
answers53
ViewsI'm looking for a manual for my Shopmate 5200AT4 radial arm saw. Can anyone help?
11
answers1200
ViewsI'm going to hang a six foot swing on my screened in porch and I think I have a problem. The roof of the porch is slanted, and the 4x8 beam that I'...
1
answers1013
ViewsCould anyone tell me where I might locate an owners manual for an old ***** Craftsman Belt Sander Model# 315-11720. I found the parts list and a d...
100
answers2905
ViewsJust inherited 1950's Craftsman table saw from my Dad. I've created a .pdf version of the operating manual. If you're in need, I'd be glad to e-mai...
37
answers1457
ViewsI also have an old Craftsman table saw mdl# 113.295752; motor part # 62505. Any idea where I can get a replacement motor - 120v; 12A; 3450 rpm; 60...
0
answers253
ViewsI don't have a blade problem, I have a motor problem. I used to have just ONE of these 6110, then I sold it... big regrets. So now I have TWO tha...
2
answers225
ViewsI don't have a blade problem, I have a motor problem. I used to have just ONE of these 6110, then I sold it... big regrets. So now I have TWO tha...
0
answers57
ViewsAttention all contractors, treasure hunters, and lovers of construction -- BOB NEEDS YOUR HELP! To re-install the original hinges removed from a...
1
answers827
ViewsThis should work for you: http://www.tools-plus.com/power-tools--electric-.html then select mitre-saws and then put #34-010 in the search...
1
answers1155
ViewsI am building a new home with 3' overhangs 8/12 composition roof and brick veneer. I want to go maint free and mold proof on everything. Could I ...
4
answers947
Views