how to repair a pine table
hi there,we have a lge plank pine table.. we have had it for a number of years now.it was originally just coated with a clear stain, and with time....
COMMUNITY FORUM: TOOLS & WORKSHOP
over 12 years by bonniesunshine
0
answers302
Views
hanging doors
I am replacing the doors in my home and would like to know if anyone can give me an idea about what I should expect to pay to have someone install ...
over 12 years by help
0
answers467
Views
Cloudy or Milky finish
I just aquired an old (20 yr) office wood credenza. It is made of particle board with good quality vaneer. The finish in some areas seems milky or ...
over 12 years by Chip
1
answers348
Views
installing paneling over drywall and putting up chair rail
can anyone tell me if you have to remove drywall to put up panels or can i just put right over drywall. and if i put up chair rail do i have to cut...
over 12 years by SuzanneS
2
answers865
Views
Bathroom counter top
When our house was built 20 years ago, we wanted 2 sinks in the master bathroom. However, the builder failed to let us know just how small that "m...
over 12 years by 4-K Carpenters
1
answers416
Views
Cloudy or Milky finish
I just aquired an old (20 yr) office wood credenza. It is made of particle board with good quality vaneer. The finish in some areas seems milky or ...
over 12 years by manoross
0
answers960
Views
How do you install a handrail & ballesters?
How do you install the ballesters into a wooden handrail on new stairs we had built?
over 12 years by rpxlpx
1
answers591
Views
Minor Repairs - Laquer Finishes
Has anyone found a tried-and-true method of spot refinishing stained-laquered pine and oak casing, mouldings, etc? I want to do some minor repairs...
over 12 years by Chip
2
answers899
Views
Crown molding
I am trying to cope an inside corner of crown molding and not being very successful. Could someone tell me the proper angles to cut the coped boar...
over 12 years by bjeffress
1
answers210
Views
crown molding
When installing crown molding, what determines which edge is the top? Also, can it be coped, or only cut with compound angles?
over 12 years by bjeffress
2
answers657
Views
fluted casing
i need to make fluted casing. the flutes must stop several inches from each end of the board. they also need to shallow out and come to a point at ...
over 12 years by twhit26
0
answers236
Views
built-in curio cabinet
I took down 2 cabinets. I now have a recessed wall, 2'x4'x2' and is 7 1/2' high. I want to mirror the back wall, put in glass shelves, frame in th...
over 12 years by Dust Bunny
0
answers131
Views
kitchen cupboards
My wooden kitchen cupboards have no knobs or handles for opening. They are stained and varnished oak. They have become dark and gummy on the corne...
over 12 years by Bearoness
2
answers966
Views
Utility Room
My house is pier and beam. I have a living area (used to be a single car garage) that is on a slab. I want to take part of that room in and make ...
over 12 years by Bearoness
1
answers346
Views
Deck Treatment
I am presently having a mahogany deck built. Any advice on deck stain or treatment?
over 12 years by lrodptl
0
answers301
Views
Building a frame in place of boxspring?
I am moving into an apartment on the third floor of a three family and the staircase will allow a queen size mattress up the stairs but not a box s...
almost 13 years by tmacrock
0
answers56
Views
Dresser
My wife wants to paint to old dressers for our children. I'm looking for some recommendations on paint and if there are any protectants from scrat...
almost 13 years by tndeck
1
answers326
Views
Steel Frame / Steel Studs / Paneling
Is it possible to hang paneling on Steel Frame/Steel Studs. House was infested with termintes. Rebuilding. Any help would be greatly appreciated...
almost 13 years by HOLLYWOOD
1
answers458
Views
Finishing Basment
I am going to finish my basement. How do I attach the treated plate for partition walls to the concrete? Thanks in advance.
almost 13 years by Raino
1
answers997
Views
Replacing Stairs
Im replacing some 40 year old stairs What I would like to no should I use the stringers that are there they seem to be ok The problem is that the s...
almost 13 years by RussR
0
answers707
Views
