columns
I have a 150+yr old New England farmhouse. It has been remodeled within the last 15 years. The problem is this. I have these huge dark wood beam...
COMMUNITY FORUM: TOOLS & WORKSHOP
about 14 years by Calene
5
answers825
Views
Crown Moulding
Does anyone know what to set the blade at when cutting crown moulding for 45*, 22 1/2*, 25* angles? I want to be able to cut it laying flat on the ...
about 14 years by Teresa
0
answers522
Views
stairways
i am searching for the calculations for building stairs. i have read both of the 'rosendahl's' books. No help atall.
about 14 years by nomad
0
answers626
Views
Structural Integrity
I've recently purchased home office furniture and placed it on the second floor of my onefamily, sidehall colonial, built circa 1983 in New Jersey....
about 14 years by jbreach
0
answers677
Views
Building an archway
I am framing in my house. i want some doorways to have arches. How do I go about doing this?
about 14 years by heavisides
0
answers334
Views
Maintaining table saw
What is the best way to make my table saw surface smooth and avoid rusting. Also scrollsaw table surface. What kind of cleaner should be used? Any ...
about 14 years by Kansaz
1
answers638
Views
Box system spiral stairs - HELP!
Does anyone know where I can get the plans for the spiral stairs Bob had on his show?
about 14 years by jstevens
0
answers240
Views
Bed rail brackets
I am looking for brackets that are installed into the ends of bed rails I am making a 4 poster bed and need to have these to complete the job .. ...
about 14 years by Kiwi
0
answers558
Views
Mitering Crown Molding
I have a compound miter saw, and I'd liketo put up crown molding. How do I cut crown molding ? I saw a previous post mentioning turningit over, b...
about 14 years by redoakdude
1
answers942
Views
Restoring hardwood floors
I have recently moved into a 38 year old ranch home in serious need of remodeling. My grandmother lived here before me and allowed the house to bec...
about 14 years by SprungJo
4
answers314
Views
Crown Molding
In new construction I am curious as to what is acceptable when it comes to caulking crown molding in the corners as well as on the sides of walls. ...
over 14 years by DR HOME
1
answers185
Views
paint stripping
i was thinking about stripping my kitchen cupboards down and staining them. the house i live in is about 25-30 years old and the cabinets hava many...
over 14 years by LisaR
1
answers741
Views
Painting Cabinets
I would like to try to repaaint my kitchen cabinets myself, rather than having them completely replaced. They are wood cabinents (but are pretty ch...
over 14 years by alpernmb
0
answers84
Views
Fine Homebuilding Discussion Board
FYISee the pro's opinion of Bob at the Fine Homebuilding's BREAKTIME discussion Group:http://www.taunton.com/fh/THREAD:Who thinks Bob Villa is wort...
over 14 years by Mikey
2
answers722
Views
lazy susans
We are building our own kitchen cabinets, and are now working on eight lazy susans. We've cut circles out of three quarter plywood, and tried gluin...
over 14 years by loader_98
1
answers547
Views
Kitchen Pantry Plans
Would like to know if there is anyplace online that I could get plans with materialslist for a built in pantry ie: 30"x84 withfour doors and slidin...
over 14 years by Ron
0
answers597
Views
Bending wood
what type of wood should I se and how do I bend it to make sleigh runners?
over 14 years by Fred Reichart
2
answers766
Views
Lightening Wood (Bleaching?)
I, too, am in the market of stipping my kitchen cabinets. The cabinets and drawers seem easy enough to strip because I will be able to remove them...
over 14 years by Sonia
0
answers926
Views
Cabinet making bits
Is it possible to make cabinet doors (rails and stiles) with a quarter inch bit? If so what bits would they be, and were would one get directions o...
over 14 years by Mike from Homeworks
1
answers347
Views
CROWN MOLDING ON TABLE SAW
I'm getting ready to put up oak crown molding in my den and I want to do it with my delta contractor table saw. I know that if I were to use a mite...
over 14 years by Mike from Homeworks
1
answers929
Views
