lazy susans
We are building our own kitchen cabinets, and are now working on eight lazy susans. We've cut circles out of three quarter plywood, and tried gluin...
COMMUNITY FORUM: TOOLS & WORKSHOP
over 14 years by loader_98
1
answers560
Views
Kitchen Pantry Plans
Would like to know if there is anyplace online that I could get plans with materialslist for a built in pantry ie: 30"x84 withfour doors and slidin...
over 14 years by Ron
0
answers612
Views
Bending wood
what type of wood should I se and how do I bend it to make sleigh runners?
over 14 years by Fred Reichart
2
answers781
Views
Lightening Wood (Bleaching?)
I, too, am in the market of stipping my kitchen cabinets. The cabinets and drawers seem easy enough to strip because I will be able to remove them...
over 14 years by Sonia
0
answers939
Views
Cabinet making bits
Is it possible to make cabinet doors (rails and stiles) with a quarter inch bit? If so what bits would they be, and were would one get directions o...
over 14 years by Mike from Homeworks
1
answers362
Views
CROWN MOLDING ON TABLE SAW
I'm getting ready to put up oak crown molding in my den and I want to do it with my delta contractor table saw. I know that if I were to use a mite...
over 14 years by Mike from Homeworks
1
answers942
Views
Belt Sander
We're having problems with a belt sander: Craftsmen model #113225900. Despite all effort, adjustments etc. the sanding belt will not stay on uni...
over 14 years by DR HOME
1
answers79
Views
air nailers
I am confused about air nailers. Do you need to buy the same brand air nails as the tool? Or are the nails interchangable as long as they are the r...
over 14 years by bink
2
answers687
Views
knoty pine wall paneling restoration
My house was built by my Father in 1954. It has lots of beautiful knoty pine walls and doors. The varnish is dried and cracking in some spots. I wo...
over 14 years by Steve C
1
answers754
Views
Floating Shelves
I saw a "floating shelf" advertised in a catalog & want to install a couple of very small ones on one wall w/ 3/4" laminated particle board. What ...
over 14 years by Steve C
2
answers112
Views
Radial Arm Saw damaged or out of tune?
Blade deflected off a small work piece. Thereafter the work arbor seems bent. I am unable to square the blade to the table as there is an excursion...
over 14 years by Steve C
1
answers911
Views
Butcher Block Wood
What kind of unfinished wood should I get for a kitchen butcher block? I've hear Maple is best, but its pretty expensive out here on West Coast. ...
over 14 years by Steve C
2
answers197
Views
tearing down a deck
i would like to tear down a huge deck off our house. deck is on the second floor. i would like to be able to reuse the material to "move" it to t...
over 14 years by Steve C
2
answers1043
Views
Plans/pattern for exterior window shutter
I am looking for plans or patterns for making shutters for exterior windows. I used every search engine available but could not come up with any hi...
over 14 years by bink
0
answers712
Views
computer monitor desk
Due to limited space, I built a computer monitor desk that is attached to the walls on 2 sides. On these sides it rests on a 2x2 that is bolted in...
over 14 years by DR HOME
1
answers147
Views
cleaning kitchen cabinets
I want to clean my kitchen cabinets of the years of grime without stripping and re-staining. Is there any product that will help me do this. I do...
over 14 years by mwestfall
0
answers729
Views
built - in entertainment center
I have a very long blank wall in my living room. This would be the right spot for a wall to wall, floor to celing entertainment center, or base cab...
over 14 years by L Morin
0
answers294
Views
oak railing
Planning to replace iron railing with oak railing on inside stairway. Any tips would be appreciated.
over 14 years by Jeff Dower
0
answers332
Views
Plans for workbench
I am looking for plans to build a sturdy workbench approx. 6 ft.wide. Any help would be appreciated.
over 14 years by Dougs78
0
answers211
Views
What tool to do this?
Need to shave off about 1/32nd inch from about 100-200 pencil size objects. Don't owna lathe but have drillpress and must be perfectly round so can...
over 14 years by SprungJo
1
answers1007
Views
