log home restoration
I am looking at a 125 yr old log home in Tennessee. It was relocated 35 yrs ago. The main house is in good shape but there is an addition off the...
COMMUNITY FORUM: TOOLS & WORKSHOP
over 14 years by ccrenken
0
answers992
Views
Framing
I need some assistance in framing a corner.I assume that an inside and outside corner are done the same way.Ca someone please inform me on how to f...
over 14 years by DomPepe
0
answers90
Views
Kitchen Island
I'm looking for plans for a kitchen island. I'd like to be able to mount standard size cabinets in it as well as a dishwasher in the center. Anyo...
over 14 years by Kevin Daugherty
0
answers238
Views
drill bits
What is the name and where can i find a drill bit that drills a square hole (i seen Bob use one)
over 14 years by Joe69
0
answers137
Views
dull polyurathane finish
Our zebra-wood dining table's poly finish is dull in several spots. Is there a safe way to restore the uniform high gloss it once had?
over 14 years by markfetner
0
answers721
Views
build workbench
help building workbench
over 14 years by wledux
0
answers1046
Views
stuck router bit!
I cannot get the bit out of my router to change it. The thing just won't turn. Any ideas?
over 14 years by jhill
1
answers720
Views
Bookshelves
Im looking for plans for Built-in bookshelvesDoes anyone no of any online?
over 14 years by jhill
1
answers1014
Views
butcher block
I have a butcher block counter top. It's in need of refinishing. I was told not to put just any type of finishing on it, do you have any recommen...
over 14 years by Mike from Homeworks
1
answers628
Views
restoring old woodwork
I am restoring the woodwork in a 100 year old house. There are nicks that have blackened over the years in the woodwork. should these be taken o...
over 14 years by DR HOME
1
answers933
Views
Redoing hardwood floor
We are scraping the black carpet pad off a hardwood floor after removing the carpet. How much do we actually have to scrap off and how much will th...
over 14 years by DR HOME
1
answers199
Views
entertainment center plans
I'd like to find some good plans for building an entertainment center. My husband wants to build one. Any ideas?
over 14 years by srudel
0
answers501
Views
Using a Mitre Box for 30 Degree Cut
I am in need of someone to tell me the correct way to cut a 30 Degree cut on a Mitre Box that does not have a 30 Degree setting. The book says it ...
over 14 years by Steve C
1
answers794
Views
new wood shop
I am brand new to woodworking. Several people have told me a table saw or a radial arm saw is the backbone of a shop. Anyone have a suggestion as...
over 14 years by Mitc
1
answers412
Views
plywood deck
Have purchased building with a large plywood porch. the porch has no roof, it is covered with rolled roofing nailed down to the floor it looks awfu...
over 14 years by scooter
1
answers224
Views
Baseboards
How do you miter the end of a baseboard that stops flat on a wall in order to add the missing baseboard to that other wall?
over 14 years by scooter
2
answers158
Views
Test of Creating Messsages
This is a test of the ability to create messages
over 14 years by scooter
2
answers932
Views
Layout for rafter cuts
This may be basic to most, but I'm recently retired from an office job and I'm trying my hand at carpentry. How do I determine the proper angle cut...
over 14 years by grranch
0
answers340
Views
mitering cove moulding
Need advice on mitering inside corners of cove moulding I know it is different than base.
over 14 years by zagerb
0
answers927
Views
Compressors
What's the best compressor for general woodworking tools. I bought a Sears compressor but am afraid it may be too small (2HP, 12 GAL). I want to ...
over 14 years by Nighthawk
1
answers963
Views
