Red-Lining & Check Prints in New Construction
Hello,My husband and I are about to break ground on our first home. Being a novice at any type of home experience I'm a little concerned about some...
COMMUNITY FORUM
over 14 years by shep
2
answers470
Views
harwood floors
Our house is 26 years old. We moved in 4 years ago and had the 1st and 2nd hardwood floors refinished. About 1 year later the floors started to s...
over 14 years by John Salisbury
0
answers1005
Views
porch covering
we have painted our front deck (uncovered) white to match our home. however the white is so bright that you have to shield your eyes from the glare...
over 14 years by DR HOME
1
answers129
Views
electrical wiring
i need instructions or a diagram for"wiring"a 240 volt 5 hp Craftsman air compressor from my shop to the service pole. Also is there anywhere I can...
over 14 years by tomlinson
1
answers919
Views
Creaking Siding
In the Winter, it is very windy where we live. On the side of our house that faces the wind, the vinyl siding creaks. Many times it creaks loud e...
over 14 years by jsprenk
0
answers1023
Views
Window Draperies
Does any body knows if there is a manufacturer which sell drapes on line.Thnaks
over 14 years by tguichon
0
answers996
Views
drill bits
What is the name and where can i find a drill bit that drills a square hole (i seen Bob use one)
over 14 years by Joe69
0
answers137
Views
Squeaky Floor
We have a squeaky floor in the kitchen. The house is about 15 years old and in the winter time the floor squeaks in certain spots. The plywood was...
over 14 years by tauri
0
answers596
Views
polishing marble
How do you polish unfinished travertine marble?
over 14 years by sps9
0
answers616
Views
dull polyurathane finish
Our zebra-wood dining table's poly finish is dull in several spots. Is there a safe way to restore the uniform high gloss it once had?
over 14 years by markfetner
0
answers721
Views
build workbench
help building workbench
over 14 years by wledux
0
answers1048
Views
Concrete Slab Porch
I have a concreate slab porch (not attached to the house). The slab has sunk and cracked in the middle, forcing up both ends. What is the best m...
over 14 years by Thomas M
1
answers174
Views
junction boxes
while upgrading a wall, I am relocating the switch. The line in the wall is too short. I plan to place a junction box at the end of the existing li...
over 14 years by Brian Wood
2
answers567
Views
stuck router bit!
I cannot get the bit out of my router to change it. The thing just won't turn. Any ideas?
over 14 years by jhill
1
answers720
Views
Bookshelves
Im looking for plans for Built-in bookshelvesDoes anyone no of any online?
over 14 years by jhill
1
answers1015
Views
Laminate Countertops
I purchased pre-formed laminate countertops for our kitchen and am about ready to begin installation. The only area I'm unsure of is the right met...
over 14 years by DavWoj
2
answers905
Views
3 way wiring
I recently purchased a new home and have begun renovating the basement I have discovered that a switch a 3 way switch has been wired incorrectly it...
over 14 years by Brian Wood
2
answers508
Views
Flourescent Lights - Garage
Last spring I had two 8 foot flourescent double tube fixtures added to an existing circuit with two 100 watt regular light bulbs and 1 four foot fl...
over 14 years by Brian Wood
2
answers653
Views
wobbiling ceiling fan
what are the easist ways to stop a ceiling fan from wobbling? I have heard to tape a coin to the top of the blade. but which blade and how do you ...
over 14 years by twbarman
3
answers930
Views
Too much heat
We have never had any control over the heat in our older home. The furnace had to be manually turned off to stop the heat. Just installed a new p...
over 14 years by DR HOME
1
answers812
Views
