COMMUNITY FORUM

himey18

03:48PM | 12/12/04
Member Since: 12/11/04
6 lifetime posts
Bvplumbing
I want to get rid of all my old galvanized pipes and replace with copper, but I am not sure of what size pipe to use. I want to replace eveything starting with the main line coming through the slab in my basement. I am a little fuzzy on how to measure the pipe so I know what I need to buy for any threaded fittings. I am a welder so I think sweating any other fittings shouldn't be a problem.

LonnythePlumber

05:54PM | 12/12/04
You probably have copper for a water service and you are going to hook to it with copper so you should not have any threaded fittings except at the water heater. If you have a one bathroom house then 3/4 inch will supply your fixtures. Soldering is not exactly the same as welding as you probably realize. You may want to replace just one fixture branch first to make sure your soldering will be okay.

We go by interior pipe sizing in plumbing. The outside of 3/4" copper is 7/8". The outside of 3/4" steel is an inch.

carl21l

09:12PM | 12/12/04
Member Since: 03/21/04
173 lifetime posts
to meet code, all of your soldering on plumbing must be made with leadfree solder using leed fre solder paste. I use Otay #5 myself. I have found that for a good solder connection on 3/4 copper fittings you really need to use a MAPP torch and MAPP gas to get the fittings hot enough for a good solder wick action.

JMHO

Carl

darwin802

01:29PM | 07/28/07
Member Since: 07/27/07
1 lifetime posts
you just put the flux on, heat up the two peices, touch the solder to the copper and the sloder follows the flux, right?

MistressEll

06:02PM | 07/28/07
Member Since: 01/30/05
361 lifetime posts
You need to burnish and clean both sides of the intended joint with emery cloth first.

It is also crucial you use the correct flux and solder.

Sylvan

09:10AM | 07/29/07
Member Since: 01/24/06
1452 lifetime posts
Me_office1
Soldering for a welder you can master in about 5 minutes, it is a heck of a lot easier then fusion welding as your

depending on capillary action to draw the alloy into the fitting joint.

Personally I like 95 -5 solder (95% tin 5% antimony) But the new silver bearing solders make it a lot easier as the soldering temperature range allows for a wider temperature range to play with and the silver adds to the wetting action.

To find the piping diameter look for a valve and it has the size on it.

Under standard plumbing practices it is common practice to over size the galvanized piping as we allow for this type of system to start to lose the internal area due to corrosion build up.

Normally when replacing galvanized piping it is permissible to reduce the size by one commercial size 2" galvanized can be replaced with 1.5" copper.

There are code charts that you can look into and it tells what each fixture requires (GPM flow) or if your in doubt just replace the piping with the nominal size copper.
9608-tieger_plumbing
Click_to_reply_button
Inspiration_banner

INSPIRATION GALLERY



Post a reply as Anonymous

Photo must be in JPG, GIF or PNG format and less than 5MB.

Reply_choose_button

captcha
type the code from the image

Anonymous

Post_new_button or Login_button
Register

Oversize windows let the outside in, even in a cozy cottage bathroom like this one. A roller screen and wraparound shower ... Built on a rocky island in the Drina River, near the town of Bajina Basta, Serbia, this wooden house was cobbled together ... Large steel-framed windows flood the interior of this remodeled Michigan barn with daylight. The owners hired Northworks A... Edging formed with upside-down wine bottles is a refreshing change. Cleverly and artistically involving recycled materials... A Washington State couple called on BC&J Architects to transform their 400-square-foot boathouse into a hub for family bea... Similar to the elevated utensil concept, hanging your pots and pans from a ceiling-mounted rack keeps them nearby and easy... Few projects are more fun than upcycling a vintage piece in a surprising way. Outfitted with a sink and a delicately tiled... The thyme growing between these stepping stones adds a heady fragrance to strolls along this lush, low-maintenance garden ... Decoupage is an easy way to add any paper design to your switch plate, whether it is wallpaper, scrapbook paper, book page... Twine lanterns add pops of crafty—but sophisticated—flair to any outdoor setting. Wrap glue-soaked twine around a balloon ... When securely fastened to a tree or the ceiling of a porch, a pallet and some cushioning make the ideal place to lounge. V... Reluctant to throw away any of those unidentified keys in your junk drawer? Hang them from a few chains attached to a simp... A stripped-down model, sans screened porch, starts out at $79,000. Add the porch, a heated floor for the bath, and all the... Salvaged boards in varying widths and colors make up the dramatic accent wall in this attic space. The high-gloss white of... This garden shed has been decked out to the nines. Designer Orla Kiely created the intimate home for a flower trade show, ...
Follow_banner_a
Newsletter_icon Google_plus Facebook Twitter Pinterest Youtube Rss_icon
 
webapp1