COMMUNITY FORUM

IanMacV1

10:15AM | 11/14/05
Member Since: 11/13/05
1 lifetime posts
Bvtools
building a new double bed (mattress size 54" X 75")for my son in our home -- idea is a cross between loft and hanging bed. basic box frame built out of 2" X 8". I'll make the interior box dimnension 1" bigger on each side -- so interior will be 56" X 77", and exterior will be a true 60" X 81" (using true 2" maple to match other furniture). Interior corners of the box frame will be braced. As well, interior of frame will have 2" X 2"'s strapped to the 2" X 8" to support the 3/4" or 1" plywood matress platform. The concept is to attach the head and one side to the studs, using 3 1/2" screws. the other two sides of the box will not be attached, but will "hang" from the ceiling joist via welded chain.

Wondered if anyone had any experience with a similar project, or any input into the concept.

spindaddydad

07:44AM | 12/05/05
Member Since: 12/04/05
1 lifetime posts
hey Ian,

ran across your post. This is exactly the idea we had for a bed in our son's bedroom. Bolted to the wall on two adjacent sides and supended from the wall.ceiling on the other two by chain or cable. Did you ever make this bed? and if so how did it turn out? Did you run across any unexpected situations?

Thanks,

Frank Wilkins

SPIELEO

09:37AM | 08/28/06
Member Since: 08/27/06
1 lifetime posts
I would like to know if anyone ever constructed bunk beds that hang on the wall and fold up when not in use?

Mark Hammond

07:57PM | 08/30/06
Member Since: 05/09/01
246 lifetime posts
Having a studio apartment, I once built a king sized loft bed out of full 2"x10" inch clear pine for the box part of the frame. I am a 200 lb. adult so it needed to be fairly strong. The posts were 4"x4" of the same clear pine and the upper corners were braced at a 45 degree angle with 24" 1"x6" pine. Now here is where the strength comes in. The deck of the bed that held the mattress was held in place by (I know), 2"x4"s of the same clear pine. They acted as the bed slats. They were set in place on edge into regular joists hangers. The same hangers that you would use on a house when building a deck. They were covered with two sheets of 1/2" plywood layed side by side for easy removal. The whole bed was assembled with 3/8" lag screws and bolts. We are all adults here so I will say that the bed easily held two adults and was easily dis-assembled when moving. It was later given to a friend who cut down the legs to a standard height bed. MJH

wackedgreen

04:38AM | 07/11/07
Member Since: 07/10/07
1 lifetime posts
i want a hanging bed in my room but i wanted to know about how much it would cost? the cheapestbut best quality materials? and every material needed? if any one can help that would be great

soniahg

07:25AM | 02/13/08
Member Since: 02/12/08
1 lifetime posts
Did you ever made your hanging bed?

fivelbbass

08:48PM | 03/06/08
Member Since: 03/06/08
12 lifetime posts
I made two such beds in for my two boys (ages 5 and 3 1/2) for the room that they share. The room was barely big enough for them, their beds, dressers, toys, etc. This was what I came up with, based on a similar free standing design that I designed in college. It took about $150 and seven or eight hours for two beds, rails, and ladders. Way cheaper, and way cooler, than bunkbeds! When the rail is off and the bed is made, the cable is nearly invisible, giving a illusion of beds floating about 30" from the ceiling.

For each bed:

1) Mount two 2x4s in a corner -- one was 72" in length, the other was about 32" (the length and width of the mattress). Screw these into the wall studs using 3 1/2 inch screws.

2) Cut a piece of 3/4" plywood slightly larger than the mattress; nail it to the 2x4s from above, and secure it from below using angle braces.

3) Drill a hole in "outside" corner for a large eye bolt, fender washer, and a block of scrap wood, and a nut.

4) HERE'S THE COOL PART. Secure a 3/8" steel cable, with plastic coating, about 5 feet long, to the eye bolt using two cable clamps, and put the other end through a small hole in the ceiling.

5) Take a piece of steel pipe (Mine was left over from a plumbing home improvement job) and put it over the rafters in your attic, perpendicular to the rafters. The piece of pipe that I had was 1" pipe; I tacked it down with some little pieces that I have no idea what they are called, but look like half circles with flat parts with a screw hole. Wrap the cable around the pipe and secure it with two cable clamps.

6) the bed can be leveled by adjusting the clamps, or by turning the eye bolt. It helped to prop the bed to the exact height while I was in the attic so that I didn't need to make massive adjustments once I got back downstairs.

After the initial construction, I framed the rest of the plywood w/ 2x4s, which makes it a little stronger. My kids LOVE them. I've been up there with all three of my kids (I also have 2 year old daughter) at once (about 250 lbs total) and the bed didn't even budge an inch -- it's rock solid. The cable alone is rated for 800+ lbs.

There's more nuances to this. (How high is it off the floor? How did you make the rails? How did you make the ladders?) Reply if you want photos or more information. I'm happy to share. Good luck!

p.s. I saw this post prior to making the beds, but with no info -- I hope this helps you out!

dreama333

09:15PM | 03/07/08
Member Since: 03/07/08
1 lifetime posts
Hi,

your plans sound exactly what im looking for. would pics be available or a lil more detailed intstructions would be helpful. thanks in advance for your help.

fivelbbass

07:06AM | 03/09/08
Member Since: 03/06/08
12 lifetime posts
Here's photo of my son John's bed. Notice that you can't see the steel cable that secures one corner -- it's not really "floating" in the air!
4845-photo_of_hanging_bed

jgll60

03:10PM | 03/09/08
Member Since: 03/08/08
1 lifetime posts
That bed is too cool. My daughter is looking into getting a loft bed and when I showed her the hanging bed, she said she wanted that instead.

Her room is very small so this is a perfect solution. Thanks for the pictures. Jenn

Jenn
Click_to_reply_button Inspiration_banner

INSPIRATION GALLERY



Post a reply as Anonymous

Photo must be in JPG, GIF or PNG format and less than 5MB.

Reply_choose_button

captcha
type the code from the image

Anonymous

Post_new_button or Login_button
Register

Follow_banner_a
Newsletter_icon Google_plus Facebook Twitter Pinterest Youtube Rss_icon
 
webapp1