10:07AM | 01/02/03
Member Since: 01/01/03
35 lifetime posts
I'm doing some remodeling, and have discovered all sorts of problems. The panel has more installed circuits than it's rated for. Some large-amperage circuits seem to go to systems that don't exist. Three of those curcuits are aluminum wiring, and some of the existing copper circuits appear to have more outlets and fixtures than the NEC allows. (8 plugs and two lights on a 15 amp/14 ga cirsuit, for example).

Replacing the aluminum is a given, and I can handle that. What about this panel?

If I hire an electrician, I know it's gonna run over a grand. If I provide all the materials, will it save me anything? Is is ridiculous to do it myself with an electician to check it before it goes live? Although these things look like a rat's nest, it's not hard to wire something like this, although I can foresee issues with having enough length to make connections. Is there no other alternative than to hire someone?

Anyone stared this problem in the face before?

Electrical Inspector

01:56PM | 01/02/03
Member Since: 09/27/02
73 lifetime posts

if in fact it is your intent to 'wire it all back to the panel' and hire an electrician to energize it i would suggest you make arrangements with said electrician beforehand.

you see, we are usually held liable for what we energize, so in effect the electrican is vouching for your work.

good luck

Tom O

02:08AM | 01/03/03
Member Since: 09/17/02
477 lifetime posts
If you do not have a problem tripping your breakers, and the wire sizes are correct, there is no hazard having "multiple" circuits on one breaker. One thing to check for is that the breaker lug is listed for more than one wire (read all the little tiny labels on the breaker). If the breaker isn't listed for 2 conductors, you can make a splice so that only one wire goes to the breaker.

There is no limit to the number of receptacles on a circuit in a house, your local code may vary.

If you have some circuits that appear to not be in use, disconnect them, remove them from the box & cap off the ends, also close off the hole in the enclosure. Now you can split up a few of the doubled up circuits.

Splicing in the panelboard enclosure is permissible, so short wires shouldn't be a problem.

When the customer supplies the material, I deduct what I would pay for the material, which is usually less than what you will pay. Also, my warranty does not cover any customer furnished material.



07:01AM | 01/03/03
Member Since: 01/01/03
35 lifetime posts
Well, with the remodeling, I want to add outlets and light fixtures to those that already exist. The residential construction handbook that I have recommends no more than 8 outlets/fixtures on a 15A circuit, and if I want to add more I have to change something. The aluminum is another critical change. I'd rather rewire with 12 ga wire and run 20A circuits according to the specs I have, and know that it's the best I can do rather than simply leaving AL wire in use and cramming more stuff into circuits that I believe are maxed out already.

The critical problem for me is the panel. I have 18 breakers totaling 370 amps in a 200 amp rated box which uses a 60 amp breaker as a main power shutoff. So no matter what's in there, if I have AC, oven, range and a few other things on I'll exceed 60A and trip the whole house. There's no main power switch other than this 60A breaker, and I strongly suspect this is a NEC violation. AL wire in that box for feeder cursuits is clearly a violation.

I'd like to run new feeder circuits to address the above problems and upgrade the box to one that has a main power switch, and has some extra space. Part of the basement remodel is installing my dream aquarium which will need a new circuit, and there's currently no space in the existing box.

I'm doing as much of this work on my own as possible since I'm not made of money and enjoy the effort. Wiring isn't hard, it's just attention to detail and knowing the proper methods.



Post a reply as Anonymous

Photo must be in JPG, GIF or PNG format and less than 5MB.


type the code from the image


Post_new_button or Login_button

The “Briolette” faceted glass sink from Kohler measures 17.5” wide and is sure to catch the eye—as it does the light. $707.50 Filling an underutilized area beneath the stairs is a smart way to save space. Doing so with a stash of wood, however, is ... For some decorative recycling, consider burying old bottles upside down to create edging for your garden beds and walkways... Chocolate-colored walls and large window frames allow the exposed wood beams to take center stage in this small screened p... If you're not crazy about the idea of commingling plants and pool, this modern variation may be more to your liking. The s... Yes, a freestanding garage can become its own tiny house. Artist Michelle de la Vega has all the comforts of a modern resi... There’s nothing like a new set of cabinet hardware to refresh a room. The possibilities are endless: Go modern, rustic, or... Filling an underutilized area beneath the stairs is a smart way to save space. Doing so with a stash of wood, however, is ... Like no other floor type, a checkerboard design works wonders to underscore the retro kitchen theme. Vinyl flooring, ceram... Twine lanterns add pops of crafty—but sophisticated—flair to any outdoor setting. Wrap glue-soaked twine around a balloon ... When securely fastened to a tree or the ceiling of a porch, a pallet and some cushioning make the ideal place to lounge. V... Incorporate nature into your lighting scheme by securing a dead tree in a concrete mold and draping your pendant lamp from... For the cost of a can of exterior paint , you can totally transform your porch. Paint the floor a hue that complements yo... In this urban apartment, a standard-issue patio became a serene and green perch by replacing the typical concrete with gro... If you put the washing machine in the mudroom, you can stop the kids from walking through the house in dirty, grass-staine...
Newsletter_icon Google_plus Facebook Twitter Pinterest Youtube Rss_icon