Cut nails - Page 9 - Search Results

crown molding end cut

What is the cut at the end of a crown molding where it stops? That is when it ends and does not meet another piece of molding. Our foyer molding stops at the end of the wall where the stair wall starts. We want to do this in another house. It appears to …

half round window caseing how to cut straight boards into round opening

i have three half round windows. 34 and three eighths high x 70.25 wide am putting 3.25 trim around the top nee to figure out how to segment it and what angle to cut ach piece at also have 2 17x35 half rounds to do also hope someone can help me thanks

Cut Bottom

Generally speaking you cut the bottom only and no more than about 1" max.

crown up.

I would not replace it, just cut about a third of the way into it from the bottom to relieve the tension, and then sister another right alongside of it, using construction adhesive and plenty of 12d nails Excellence is its own reward!

Finishing nails for crown molding

I am getting ready to put up crown molding in my home and was wondering what size finishing nails (16 or 18) do I want to use. Also, is a nail gun something that can be used on crown molding? Any help would be greatly appreciated. Thanks.

Inside Mitre Cut on Crown Modeling

I need to know how to cut a compound mitre cut for a Inside corner on crown modeling. Also it's a corner cabinet so there's two angle's, Im not sure what the degree of the angle's are. Any help would be much appreciated.

Where can I get laminate countertops cut/a cabinet door cut to install glass

I would like to install a laminate countertop but have no idea where I can get a 10ft piece cut. Also I have a cabinet door that I need to cut out to replace with glass. Any suggestion on where I may go to get these cut? Thanks!

100 yrs........Math.....

… -bracing" in an existing structure is kinda tough......the top nails are normally driven while the floor structure is open (the … diagonal braces in the joist bays is a challenge "...measure once.....cut twice....throw that one away and cut a new one...." …

how to cut a notch in a 2x4

I'm new to construction and need basic How-to instructions to cut a notch in a 2x4

Vinyl siding/nails popping out of clapboards underneath

… boards seem to be curling some, and the nails seem to be backing themselves out of the … . Obviously, I will need to drive these nails back in before I install the siding, but how concerned should I be that these nails will continue to back out and bulge …

Need to cut asbestos siding shingles

… a window bigger on one side of our house. We've removed the asbestos shingles around the area, but we know that we'll need to cut some of them to fit near the window's edge. What's the best way to do this? They are so brittle! Thanks in advance!

roof repair

… MAY be able to either pull them out or even cut them where EACH 'end' goes through the shingle. (If you cut 1 end, you'll need to 'bend' the … be installed.) Make sure you have the right length nails so measure the 'thickness' of the roof's …

Installing Hardi-Plank siding

… do not need to do any thing special for hardi-plank. Cut it with a skillsaw and an old carbide blade. Nail with hot dipped galv 8d nails, nail along the top 1" of the siding so that the nails do not show when covered with the next piece of …

OSB roofing

… it. What's the best way to cut OSB? Am I using the right … and blade? Also, once I get it cut, should I attach the sheets with a nailgun? I hand nailed 8 penny nails when I built a shed, but … of time here. Any thoughts on what kind of gun/nails to use?

siding that buckles

It was probably installed incorrectly. The nails must be 'loose' (not hammered down tight) so that the siding can … by hand. Should have some movement. Another possibility is that it was cut improperly and the expansion areas on the ends were trimmed off?