Spraying On and Painting a Heat-Reflective Pool Deck

Project: Storm-Ready Design, Episode 10, Part 1



Bob is on the newly poured pool deck as Don Humphrey and his crew apply the Texture-Krete finish to the top edge and traffic area of the pool. The concrete is treated with a bonding agent before the cement-and-polymer spray coating is sprayed on in textured drops. A crew member knocks down the drops with a trowel as soon as the wet gloss starts to fade. This 1/16-inch textured finish is painted with an acrylic masonry paint, applied in two coats and sealed. This deck is cool and slip-resistant and is pitched toward a drain that takes dirty poolside water away from the pool. In the house, Leonora Campos from Toto is in the guest lavatory where the sleek, two-piece Washlet 6300 with remote control wash, dry, and deodorize settings eliminates the need for toilet paper and repeat flushing. These ultra low-flow washlets flush clean the first time, save energy, water, and trees, and are more popular in Japan than microwave ovens. In the garage, Ernie Hutto from DAB Garage Doors is on hand for perhaps the most important feature in this storm-ready house – a hurricane-proof garage door with reinforced panels and tracks to prevent twisting, blow-in, and ultimate house failure.
Part 1: Spraying On and Painting a Heat-Reflective Pool Deck
Don Humphrey is spraying a cement and polymer mix from Innovative Concrete Technology called Texture-Krete 2000 onto the pool edge and deck in Punta Gorda, Florida. He moves in a circular motion to splat the cement mix onto the deck. As the gloss begins to leave the spots, a crewmember follows behind to knock it down with a trowel. This removes the pointy tops but leaves a 1/16-inch stucco pattern to the pool deck to make it easy to walk on. The deck is cleaned and scratched to remove any rough points before Humphrey and his crew apply an acrylic paint to the textured deck surface. The key to a well-sealed surface is to roll the paint firmly into all the nooks and dips in the surface. Bob talks about the embedded deck drain set in the concrete that is pitched slightly away from the pool. Excess water and dirty deck water drains away from the pool and is carried off to the sides of the pool deck by the deck drain. Humphrey applies two coats of paint and a topcoat for protection. The deck can be maintained with gentle soap-and-water washing to prevent any white spots from drying chlorine on the painted surface. Humphrey says the paint should last three to five years before it is redone. One key to maintaining the surface is to avoid abrasive cleaners or power washing. Should any mold or mildew attack the surface, Humphrey suggests using a mild bleach-and-water solution to kill the mold. The oyster color the homeowners have selected should wear well and stay cool in the hot Florida sun.
Part 2: Ultra Low-Flow Toilet Installed
Part 3: Hurricane-Resistant Garage Doors
When hurricanes strike again and again, as they did in Florida in 2004, the effects are devastating. Bob Vila and crew work to completely rebuild a damaged house, using new standards for storm-ready housing. Along the way, Bob investigates a home's vulnerabilities in extreme weather and learns why some building systems fail and others succeed.

Also from Storm-Ready Design

  • Episode 1 - Rebuilding to Beat a Hurricane

    Pg-1

    Description:
    Bob is in hurricane battered Punta Gorda, Florida, to build a storm-ready home in Season 1 of Bob Vila. Bob visits two homes in the same neighborhood, one that was completely destroyed by Hurricane Charley in August 2004, the other that was built to exceed hurricane codes and was left unscathed by hurricane winds and water from the same storm. Scott Buescher of Mercedes Homes shows how enhanced building practices and technologies can create a storm-resistant home, while Lieutenant Governor Toni Jennings and Secretary of Community Affairs Thaddeus Cohen discuss rebuilding Florida. Building inspector Randy Cole and Mercedes Homes’ Jesse Gonzalez review the site and watch the pour of a three-stage steam wall that sits below grade and ties the slab foundation to the ground. The resulting foundation will resist water penetration from storm surge by allowing water to move around the foundation without encountering entry points. Bob reviews the house plans with Scott Buescher of Mercedes Homes and learns how the house is constructed as an integrated system. Building connections are emphasized and reinforced rebar and steel mesh are extended from the stem wall to the roof line in preparation for the solid concrete pour that will form the exterior walls.
  • Episode 2 - Building a Reinforced Concrete House

    Pg-2

    Description:
    Bob recaps construction of the stem-wall foundation and integral concrete slab, the vertical steel reinforcing, steel mesh, window bucks, headers, and spacers put in place for the cast-in-place concrete walls. Cameron Parker and the crew of Solid Wall Systems spray the aluminum wall forms with an organic oil spray to prevent adhesion from the concrete and set the forms for the pour. Bob joins Wayne Sallade, Charlotte County Emergency Manager, to review cleanup, demolition, and repair one year after Hurricane Charley. sallade explains that housing built in the 1960s through the 1980s, before the Florida Unified Building Code, had stick framing, gable roofs, and siding. "It didn't stand a chance," he says. Looking at surviving 1920s Florida architecture, it's clear that unified construction, concrete walls, protected windows, and hip roofsare the way to design wind-resistant homes. Back on site, bob watches the pour, learns how the walls and window openings will be vibrated to eliminate voids, and sees the bracing set to hold the walls square before leaving the site to let it cure overnight. Once the forms are removed, Jesse Gonzalez explains how a traditional three-coat Florida plaster job will complete the exterior once the structure has cured for two weeks.
  • Episode 3 - Building a Storm-Ready Roof

    Pg-3

    Description:
    This episode of Bob Vila will focus on roofs, how they are built and tied down to keep structures safe. Leslie Chapman-Henderson from FLASH, the Federal Alliance for Safe Housing, explains how FLASH brings information about safe housing technologies and practices to homes across America, to protect them against floods, winds, hail, and wildfires. Chapman-Henderson explains how a connected house works as a system to beat back the pushing and pulling forces of wind. Randy Shackelford of Simpson Strong-Tie shows Bob the embedded truss anchors that will tie down each truss member of the roof framing, as well as retrofit tie-downs and heavy connectors designed to fight wind uplift forces. Jesse Gonzalez walks Bob through the steel-framed interior that has a master suite and bath, and lots of open space. Bart Cox of Hanson Roof Tiles brings factory-extruded cement clay-look tiles that are pre-drilled for mechanical installation. Dave Peck of D. Peck Roofing explains that stiffer 5/8-inch plywood sheathing, 30 pound felt that is nailed, hot mopped with asphalt, and covered with 90 pound felt makes a strong, water-resistant roof deck for the tiles. Metal nailer boards keep cap tiles in place when wind strikes.
  • Episode 4 - Impact-Resistant Windows for a Storm-Ready Home

  • Episode 5 - Storm-Ready Doors, Fiberglass Wallboard, and Power Backup

  • Episode 6 - Faux Columns and a Gunite Pool

  • Episode 7 - Storm-Ready Stucco Paint, Foyer Tile, and Textured Finishes

  • Episode 8 - Concrete Color Staining, Soffits, and Energy Efficiency

  • Episode 9 - Kitchen Finishes for the Storm-Ready House

  • Episode 11 - Sustainable Landscaping, Water Use, and Termite Control

  • Episode 12 - Hurricane-Safe Pool Structures, Pool Mechanicals, and Safety

  • Episode 13 - Surge Protection, Plumbing, Bamboo Blinds and Garden

  • Episode 14 - Completing the Punta Gorda Storm-Ready House


Inspiration_banner

INSPIRATION GALLERY

Partners' Latest
 
webapp2