deck addition confusing
I looked all over the Weyerhauser sites and couldn't find that program, can you let me know where it is? I'm assuming you mean a 2x8 bolted to e...
I looked all over the Weyerhauser sites and couldn't find that program, can you let me know where it is? I'm assuming you mean a 2x8 bolted to e...
11
answers259
ViewsThis is the reply from correct deck: "For people that are having problems with mildew coming back after cleaning we do have a product called Dec...
241
answers186
ViewsCall the local carpenters union hall or a local builders group and ask if they have any references. There are literally thousands of prefab & cust...
1
answers319
ViewsFirst check with the local building dept. most wetlands are protected sometimes with up to a 50' set-back. Then I'd look at the blocks' web site...
1
answers15
ViewsI'll see if I can have a rep come by and provide an answer? http://www.altereagle.com/ http://decks-ca.com http://kingofcrown.com Alter Eagle...
241
answers738
Views...hmmm. Well, first off that wouldn't be the "best site" if you want to know about the new treatments, the best site would be the source: h...
7
answers445
ViewsOf the hundreds of decks I've built over 30 years none have had pressure treated wood as a finish. This is from NY & ONT in the 80's BC & WA in th...
6
answers810
ViewsJust flip the piece over, the screws will line up. http://www.altereagle.com/ http://decks-ca.com http://kingofcrown.com Alter Eagle Constru...
4
answers13
ViewsMeasure from the inside of the form in the corner 6' one side, 8' on the other then across the diagonal ( hypotenuse )will be 10'. That is the ...
2
answers720
Views26 gauge galvanized iron sheet.. basically any galv. material would work here is a pdf detail I found: http://www.co.el-dorado.ca.us/building/PDF/...
4
answers234
ViewsUsually it's repairable.... but you usually have to replace one or two joists, so it can get intensive if the tub needs to come out to get access u...
1
answers827
ViewsIt's easiest to mark it in place & make a half lap joint. But all the inside angles will add up to 180... 67.5 + 67.5 + 45 =180 or 45 + 45 + 90 = 1...
1
answers38
ViewsHow wide it the gaps? A good painters grade caulking will usually fill that line. http://www.altereagle.com/ http://decks-ca.com http://kingofc...
2
answers273
Views...the plunge can be locked in position too. A neat trick I use for counter tops is to attach a pice of maple or oak 1x to the face (keep nails ...
9
answers845
ViewsI have a link to a site that explains that well.. it's in the crown moulding forum on my site: http://altereagle.com/forums/index.php?viewcat=6 ...
1
answers481
ViewsCode calls for p.t. rim joist w/26 ga. g.i. flashing. I'd add a ice & watershield type membrane over that and isolate it with 15# felt below. h...
4
answers185
ViewsUse a slotting cutter bit with a bearing. http://www.freud-tools.com/freudcutset.html That is a picture of one. http://www.altereagle.com/ ...
9
answers783
ViewsYou could cut the baluster profile out of flat stock, similar to victorian verandas, for a real low cost solution? :) http://www.altereagle.com/ ...
5
answers363
ViewsIt's hard to say with those dyes, try looking at the faq page of web site of the dye you used. They may offer more insight into your specific situa...
1
answers516
ViewsIf the gables are to the front then a porch may not work. Perhaps a pergola with nice columns at the entrance. You could use cedar that would gr...
1
answers779
Views