thin wooden slats
sounds like the walls were originally plastered. the thin wooden slats with spaces were used to support the plaster. when the plaster was applied...
COMMUNITY FORUM
Recent Posts
almost 8 years by carl21l
9
answers643
Views
excess arbor play
Your correct model is 113.29991 Your could have a missing arbor bearing retainer ring, but most likely problem is worn bearings. anything over .0...
almost 8 years by carl21l
1
answers185
Views
screwdriver a no-no
use a piece of 3/4 inch hardwood to wedge the blade. a screwdriver can damage the teeth of the blade and can leave scratches on the table surface...
almost 8 years by carl21l
4
answers530
Views
old tools
tomz71ss: the items that you have listed, I would personally consider as canadates for a garage sale. without knowing the details of condition an...
almost 8 years by carl21l
12
answers509
Views
miters
sounds like a good reason to buy a miter saw. what can be done is to cut a piece of 2x6 wood on a 45 angle and fasten it to the miter gague, the...
about 8 years by carl21l
1
answers417
Views
saber saw
I have that saw with the kit box. The saw has a bad speed selector board on it. JMHO Carl
about 8 years by carl21l
5
answers459
Views
freeloaders source for the manual
http://www.owwm.com/MfgIndex/Detail.asp?ID=222 look at all manuals, it is the last listing under radial arm saws. Please donate to the site to...
about 8 years by carl21l
11
answers336
Views
model number
look for a tag with number format 123.45678. the tag should say craftsman also. the tag will normally be mounted either on the table metal frame,...
about 8 years by carl21l
1
answers503
Views
old tools
Yes, there is a market for vintage power tools. give a list by make and model and i can give you an indication of the interest in them. Old casti...
about 8 years by carl21l
12
answers313
Views
cleaning mower deck
I use a blow nozzle on my air compressor to blow wet debris from the underside of the mower deck. be sure to wear safty goggles as there is a lot ...
about 8 years by carl21l
5
answers102
Views
lathe parts
since you entered part numbers for what you need, I suppose that you have the owners manual and parts list. the manual or parts list should tell y...
about 8 years by carl21l
5
answers600
Views
nailers and mdf
I have found that mdf is difficult to nail with nailers. forget the electric as it is underpowered. when I tried using a 18 gauge nailer, it was ...
about 8 years by carl21l
2
answers910
Views
shear pin
do not use anything but the correct shear pin. the purpose of the shear pin is to protect the motor and any gears and/or belts in the drive to the...
about 8 years by carl21l
1
answers430
Views
it is do-able
you will need to cut an opining on each side of the ridge board. most manufacturers recommend removing 3/4-1 inch of sheeting on each side to allo...
about 8 years by carl21l
1
answers511
Views
103.0213 saw
the saw is from the mid to late 40's the price varies depending on condition. I have seen them on ebay bring $15 to $50 for a fully restored saw....
about 8 years by carl21l
1
answers669
Views
Pink Tool Belt on the Job Site
imagine a 290 pound 6-6 carpenter wearing the pink belt. are you going to make fun or laugh at him?? :) :o) JMHO Carl
about 8 years by carl21l
4
answers63
Views
mower
your mower has a Tecumse engine. both the owners manual and the starter assembly are available form the S ears parts store. You can also use a le...
about 8 years by carl21l
4
answers821
Views
preasure switch wiring
normally on the preasure switch the green wires are attached to the ground screw in the box. the terminals on the switch should be marked line o...
about 8 years by carl21l
2
answers485
Views
saw blades
i have not found a source of 8 inch blades with 1/2 arbor. what I use are 5/8 arbor blades with an arbor adapter for 5/8 to 1/2. these can be fou...
about 8 years by carl21l
1
answers762
Views
search tomo
in the uiper left of the screen is a search box. type in Tomo and hit go. JMHO Carl
about 8 years by carl21l
1
answers920
Views
