cutting large wooden letters
Most of those places use a pantograph machine connected to a router. Vermont American sells a letter cutting stencil for use with a standard route...
COMMUNITY FORUM
Recent Posts
about 8 years by carl21l
1
answers420
Views
see this web site
http://www.c-cure.com/servref/techsupp/115.htm JMHO Carl
about 8 years by carl21l
2
answers363
Views2
answers955
Views
new motor
you can get new motor from delta: http://www.deltawoodworking.com/index.asp?e=4941 JMHO Carl
about 8 years by carl21l
1
answers904
Views
flush cup pull
http://www.door-hardware.net/misc.html JMHO Carl
about 8 years by carl21l
1
answers481
Views
table saw arbor
Byron, Saws was made by emerson electric for craftsman and ridgid brands. the craftsman tools made by emerson all have model numbers of 113.xxx...
over 8 years by carl21l
1
answers813
Views
motor direction
some motors can be reversed, and others cannot. the name plate on the motor will normally tell you if the motor is reversiable. if the motor ha...
over 8 years by carl21l
1
answers719
Views
blower wont start
I just had the same problem on a furnace. I concluded the blower motor was bad. When the repairman came, he did the same checks as you and I ded a...
over 8 years by carl21l
3
answers478
Views
gfci protected
the outlet in the laundry is connected to the load side of the gfci outlet. that is required by code in most areas as there is water in the laundr...
over 8 years by carl21l
6
answers506
Views
door
cross section of door view from top latch ----------------------------- hinge \ / | -----------------...
over 8 years by carl21l
3
answers554
Views
paint sheild
I use a 12 inch mudding knife as a sheild between the carpet and the wall. inset the knife and use it to push the carpet away from the wall and ap...
over 8 years by carl21l
1
answers110
Views
deburr copper
I have found that a pocket knife with a small blade is very good for de-burring the copper pipe and I prefer it to the blade on the cutter. An yes...
over 8 years by carl21l
9
answers941
Views
hardwood floors
personally, I would hire a floor refinisher to at least do the sanding of the floor. to remove the black stains from the tacks, use wood bleach, t...
over 8 years by carl21l
1
answers393
Views
PIE
P = power in watts I = current in amps E = voltage in volts P=IE use your math to get any value knowing 2 of the three values. I use a bo...
over 8 years by carl21l
2
answers4
Views
barn roof
when I built my new 16x20 shed, I first laid out the rafter patern on the floor and constructed the rafters as modified trusses. Then I framed and ...
over 8 years by carl21l
5
answers691
Views
door problems
I would start by cleaning and then lubriocating the tracks, hinges, guide wheels and drive mechanism. Lubricat with a silicone spray lubricant. if...
over 8 years by carl21l
1
answers546
Views
adobe vs "brick"
when you said brick i was thinging clay brick, not adobe. try this site for help with makin dobe bricks. http://www.cahe.nmsu.edu/pubs/_g/G-521.pd...
over 8 years by carl21l
3
answers157
Views
code
many localities require lead free solder on any piping that is in the home or supplying the home. JMHO Carl
over 8 years by carl21l
5
answers638
Views
brick
do you own a kiln capable of firing brick?? if not, you need to purchase the brick at a home center or building supply center. JMHO Carl
over 8 years by carl21l
3
answers25
Views
