Patience
You have used oil based poly. this is slow drying and if the temperture is low or humidity high, then the drying time is extended. I have seen t...
COMMUNITY FORUM
Recent Posts
over 8 years by carl21l
1
answers673
Views
flux
I use the Otay brand leadfree soldering flux. also I have vfound that a propane torch takes too long to heat the pipe-joint causing bad solder con...
over 8 years by carl21l
5
answers559
Views
as seen on ebay
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=20791&item=4342181874 I have dealt several times with this vendor with no problems. JMHO...
over 8 years by carl21l
1
answers767
Views
capacitor
did you check with the capacitor manufacturer or with the s e a r s parts? JMHO Carl
over 8 years by carl21l
4
answers672
Views
pipe noise
a similar problem was shown on ask this old house. combination of leaky flapper valve and worn seal in the ballcock. they replaced the flapper to...
over 8 years by carl21l
2
answers345
Views
saw blades
the more teeth, the finer the cut will be. also, when cutting any cut where a very fine cut is desired, the slower the cut you make, the better th...
over 8 years by carl21l
2
answers65
Views
do the search
here: http://www.acehardware.com/product/index.jsp?productId=1444718 JMHO Carl
over 8 years by carl21l
2
answers148
Views
door opening
add 2.5 inches to the door size for width and 1.5 for height. if you buy a pre-hung door (recommended for DIYer) the instructions with the door gi...
over 8 years by carl21l
2
answers810
Views
cutting boards cleanliness
I have made it a practice to periodically resurface the board by planing or sanding to remove the knife nicks which can trap debris from the cuttin...
over 8 years by carl21l
4
answers305
Views
re fire damage
what does your local inspection/permit departments say about repairs to the fire damaged house?? oft-times if there is that much damage, they will ...
over 8 years by carl21l
2
answers150
Views
preasure regulator
it is possible that you have excess preasure on the supply to the heater. I had your problem and found that the regulator was bad. use a preasure...
over 8 years by carl21l
1
answers729
Views
more light
I have found that painting the garage ceiling with high luster white paint will give the effect of having more light. also having fixtures with re...
over 8 years by carl21l
6
answers392
Views
well Doug
I said give the cat half rations, in other words feed but keep it hungry. and yes give it water and a liter box JMHO Carl
over 8 years by carl21l
10
answers209
Views
Rat Cat
I agree with Doug. Leave a cat in the crawl space for several weeks. put cat on half rations so that the cat getw very hungry and decides that ki...
over 8 years by carl21l
10
answers842
Views
check this manual
http://files.owwm.com/PDF/Craftsman/113-20650.pdf JMHO Carl
over 8 years by carl21l
4
answers547
Views
crawlspace access
check in your closets for an access door. one of the houses that I owned in the past had the crawlspace access in the floor of the closet in one ...
over 8 years by carl21l
4
answers168
Views
mixing
you can mix latex with latex. you can mis oil with oil. I only mix when they are from the same manufacturer. JMHO Carl
over 8 years by carl21l
1
answers86
Views
blade lock
I use a piece of 1 by wood to block the blade, therefore no chance of nicking a carbide tooth or dulling a steel tooth. use the same on a table sa...
over 8 years by carl21l
6
answers716
Views
warranty
the s*ars brand tools are/were less expensive than the craftsman and are not covered by the craftsman warranty. the greater expense of the craftsm...
over 8 years by carl21l
1
answers510
Views
