Filter Grill
Your COleman furnace has the filters on the face is that right? or is there a flat panel and behind the panel up above the furnace inside the sheet...
COMMUNITY FORUM
JGRIZZ
Member since 12/16/04Recent Posts
over 8 years by JGRIZZ
6
answers345
Views
jgrizz
You cant, the bearings and shaft and that motor or the blower wheel and its bearings are bad. AT this point live with it, because it's too old an f...
over 8 years by JGRIZZ
1
answers562
Views
Sounds like dirty air filter.
Could be that the air filter is so dirty its causing the sheetmetal to colaps when the blower starts and stops.
over 8 years by JGRIZZ
6
answers415
Views
Ignition Problem
Could be that you have the polarity incorrect into the furnace, or on the hot side of the ignition control. Or could be that there is a fuse blown ...
over 8 years by JGRIZZ
2
answers947
Views
Bower
the low speed on your blower may be bad. In the fan on position the blower uses high speed. The blower in heating is usually turned on now adays by...
over 8 years by JGRIZZ
3
answers587
Views
Intermittent Firing
I need a little more information, how old is the unit. What efficiency is it? Does it have metal or PVC vent system?
over 8 years by JGRIZZ
1
answers984
Views
That is probably a bad flame sensor
Either a bad flame sensor, or bad connection at the flame sensor. Make sure you have a good ground to the unit and you may check the polarity to th...
over 8 years by JGRIZZ
2
answers806
Views
BAD pilot Valve
You Probably have a bad pilot valve in the main valve--its unrepairable. You must replace the entire Valve! The safer bet and the more cost effecti...
over 8 years by JGRIZZ
2
answers124
Views
R & W terminal
Because its a wall furnace and ones face has to be near the burners to do any testing near the main valve I shall decline to offer advice. But the ...
over 8 years by JGRIZZ
3
answers74
Views
Leaking
If your friends furnace is a high efficiency furnace, it is supposed to make water when it runs and the water is piped through plastic hoses to a d...
over 8 years by JGRIZZ
1
answers192
Views
Stat Setting
Well that may depend upon the duct system, I would turn them both on full heat as high as they go, then about ten minutes later use a thermometer a...
over 8 years by JGRIZZ
1
answers647
Views
Trane Blinking code
Its probably just indicating that the furnace has power and that there is no call for heat and that all is normal. There is a code key on the back ...
over 8 years by JGRIZZ
1
answers513
Views
SOunds like your repairman wasn't sure
Sounds like he made a guess about the blower motor and he guessed wrong. I would hire someone else if I were you. This problem is common and there ...
over 8 years by JGRIZZ
1
answers840
Views
It's fine
Its just as good as anyone else out there today. Tecnhology is pretty much the same on all equipment today. Just make sure its set up right at the ...
over 8 years by JGRIZZ
2
answers821
Views
Cycling
So what you need to determine is if its a thermostat problem or a unit problem. Try setting your thermostat all the way up as high as it goes, and ...
over 8 years by JGRIZZ
1
answers248
Views
sounds like
sounds like an induced draft combustion blower motor. Also sounds as iff the bearings in the motor have worn and te shaft is tilting slightly and t...
over 8 years by JGRIZZ
2
answers42
Views
Could be Excessive Gas Pressure!!
COuld be that the gas pressure is too high, what kind of fuel are u using and at what altitude are you? High gas pressure willc ause a high tempera...
over 8 years by JGRIZZ
2
answers560
Views
Flame Rectification
All electronic igition systems have flame rectification, or a means of proving there is a flame present in order to keep the main gas valve open. ...
over 8 years by JGRIZZ
1
answers484
Views
Sounds like a bad blower
A few things can be happening here, the most likely is that the low speed winding on the motor has burned out. Another possibility is that the blow...
over 8 years by JGRIZZ
4
answers677
Views
Sounds like a bad blower
A few things can be happening here, the most likely is that the low speed winding on the motor has burned out. Another possibility is that the blow...
over 8 years by JGRIZZ
4
answers18
Views
