Hmmmm, pump...
Thanks DanO! Guess I need to pull it apart and scope it out. Hmmmm, now I need to figure out what exactly is the pump :-) Sorry about the mo...
COMMUNITY FORUM
Recent Posts
over 4 years by k2
4
answers880
Views
Noisy dishwasher
Interesting. We try and alternate between powder and liquid dishwasher detergent, but lately we've been using primarily powder - I think Costco Ki...
over 4 years by k2
4
answers953
Views
NOISY Kitchenaid Dishwasher
Hi DanO!, our Model # KUDU03FTSS - dishwasher has started making a lot of noise. Fill and drain noises are OK. The loud noise starts when dishw...
over 4 years by k2
4
answers1058
Views
New Hardwoods on old Stairs
Howdy folks! Been quite a while since I've been on this BBS, but I have a question I'm hoping a "stair person" can help with... I have a straig...
almost 5 years by k2
0
answers322
Views
COMPRESSOR SIZE for CLEAT NAILER
Greetings compressor gurus! I'm trying to lay 5/8" bamboo flooring atop an old oak hardwood floor, and my cleat nailer is really struggling. I ...
about 5 years by k2
0
answers1063
Views
molly bolts
IMHO, drapes are a big pain :-) It's best to hit into 2x4 - which will hold the weight. Failing that, check your local hardware store. There...
over 5 years by k2
1
answers398
Views
moving gas line
In my experience, it's very possible. I have done this a couple of times - well, with a plumber's help. I think one issue that most newbies d...
over 5 years by k2
1
answers352
Views
"Split" box spring
I tried googling "split box spring" and came up with some interesting links....(including the one below). It probably won't answer your question, ...
over 5 years by k2
1
answers160
Views
Burnt Odor...
I hate to say this, but probably best to replace the microwave. Burned smells can be absolutely horrible - very tough to eliminate. There are sp...
over 5 years by k2
1
answers35
Views
Disguising laundry
Just a thought. In my first place, the laundry was visible from the living room, behind french doors. I built a partition wall in front of the wa...
over 5 years by k2
1
answers993
Views
Kitchenaid d/w door latch
Hi DanO! Our Kitchenaid KUDU03FTSS has problems with its door latch. Previously, it was really hard to close - but now it's even worse-- The...
over 5 years by k2
0
answers540
Views
traverse rod...
...or, just ditch it and replace the whole thing. In my experience, trying to repair worn curtain rods (esp if they're 10 or 20 years old) isn't w...
over 5 years by k2
2
answers423
Views
crown...
In my experience, 5/8" discrepancy may seem like a lot - but it will still look like a million after you have it up. The viewer makes allowance/ad...
over 5 years by k2
2
answers321
Views
GD issue
thanks Bill, will look into Waste King and maybe another brand or two. Many thanks! Regards, -k2 in CO Moderator, Miscellaneous Forum
over 5 years by k2
3
answers791
Views
Garbage Disposal Drain Issue - Please Help!
Howdy again folks! Do all garbage disposals have their waste outlets at the same height? Wondering because our new sink is quite deep, and puts...
over 5 years by shortstack
3
answers775
Views
oh, and...
...OF COURSE you said "asphalt" driveway!, sorry! I can be scatterbrained (well, most of the time), and naturally, there are plenty of folks out t...
over 5 years by k2
2
answers683
Views
MellyNel!
Hi MellyNel! Not sure I can really answer your question but I did wanna say "Hi!" It has been a loooong time; I recall enjoying our past discussi...
over 5 years by k2
2
answers161
Views
Gable vent gap
Hi Vickie, if I understand your question, you are probably better off using wood of some kind to fill the gaps. My temptation (again, if I'm pic...
over 5 years by k2
1
answers704
Views
countertops...
What you describe is probably not a good idea. The reason I say this is because the press-board typically used for cabinetry is really crummy stuf...
over 5 years by k2
1
answers904
Views
