Painting Cedar shingles
Going to start painting the outside. Any suggestions on a roller,the shingles expose about 5 inches. Thanks.
COMMUNITY FORUM
Recent Posts
Heat loss through ceiling fixtures leading to ice dams.
The ceiling lights in my cathedral living room ceiling leak a lot of heat. The result is serious ice dams.Is there any way to seal around the lights?
about 1 year by Radiator_Steve
1
answers745
Views
Framing nailer for light use?
I'll be attempting to build at least 1 shed this Spring, Any recommendations on a framing nailer for light and sporadic use? Thanks.
over 1 year by lrodptl
0
answers977
Views
How to? 16"x16"x10' Slab.
I had to cut into my pool deck to repair underground plumbing. The opening is 16"x16"x 10 feet. If I mix this in a wheelbarrow I can only do 2 bags...
over 4 years by lrodptl
0
answers749
Views
Cutting.
I did the job with a water mist and had almost no noticeable wear on the blade.
almost 5 years by lrodptl
1
answers286
Views
Cutting 4.5" concrete patio.
I have a ruptured suction line on my pool 4 feet below the concrete patio. I have a 10" diamond tip blade but I must make 6 cuts of 6' each. Is it ...
almost 5 years by lrodptl
1
answers411
Views
Concrete pool deck repair?
I cut 3 16"x16" holes in my concrete pool deck to repair plumbing leaks. I've now refilled the holes with soil/gravel/stonedust to receive cement ...
over 5 years by lrodptl
0
answers341
Views
OK
I usually don't need help but absent a wiring diagram that included the air handler I came here.
over 5 years by lrodptl
4
answers475
Views
3 days running
3 days running and I found what opened the circuit and fixed it. 24VAC might fry a solid state circuit or a branch indicator,warning or LED circuit...
over 5 years by lrodptl
4
answers387
Views
You're smart!
Fact 1. 24VAC frying a circuit? C'mon. A Fluke electronic multimeter frying a circuit ?,Cmon.It's not a megger. Fact 2. I changed the Tstat becau...
over 5 years by lrodptl
4
answers382
Views
Fixed
3 replies from the "experts" but only sarcasm to offer,not knowledge. I'm no HVAC guy and did not know the 24V was stepped down line voltage and c/...
over 5 years by lrodptl
4
answers113
Views
Central AC unit and blower will not turn on
My Lennox HS29-036-2P Condensing unit will not turn on and neither will the blower. I have 220V at the contactor but no 24v. I changed the Thermost...
4
answers526
Views
Walkway pavers heaved
5 or 6 pavers on my walkway just heaved.What's the best fix? Should I remove a section,dig down and add a drainage mix of gravel and stonedust and ...
about 6 years by lrodptl
0
answers198
Views
removing one brick to replace with commemorative brick
I'd like to replace one brick on my fireplace hearth/platform/wall with a commemorative brick from the old Boston Garden. What would be the proper ...
over 6 years by Piffin
1
answers753
Views
Water based poly over oil based
4 years ago I finished a portion of knotty pine with an oil based poly. Any problem with going over this now with a water based poly?
almost 7 years by BruceRidenour
1
answers281
Views
Shed Floor weight bearing capability.
I have a shed with a 2x4 24oc floor 12'x16'. Any general idea how much weight this would support? Thanks.
over 7 years by lrodptl
0
answers978
Views
Knotty Pine
How about a whitewash?I was going to do my basement this way after I saw a display room at a furniture company done this way. Google the formula
over 7 years by lrodptl
1
answers228
Views
Installation problem
My last 5 questions and no replies. Why bother?
about 8 years by lrodptl
2
answers860
Views
Hardwood flooring installation problem
I'm installing a pre finished hardwood 3 1/4 inch floor in the living room. After 4 rows were installed I measured a 3/16" runout or deviation from...
about 8 years by tomh
2
answers1035
Views
Interior Pre-Hung Doors
If you have not done them yet let me add: My wife and I just hung 4 interior doors. She had never done it and I have done 3 in my life but none in ...
about 8 years by lrodptl
4
answers493
Views
