speakers
just a note about connecting and waterproofing the leads to the speaker terminals. First be sure that the polarity is the same on both ends of the ...
COMMUNITY FORUM
Recent Posts
almost 8 years by sadickers
3
answers745
Views
motor
If you want a new motor you might visit a Grainger Store or check their WEB site, although this can be hard to find what you are looking for some t...
almost 8 years by sadickers
1
answers36
Views
flooring
I guess I didn't explain it very well.. The available stair treads are only available in 48 in lengths and my required tread with is 78 inches. Se...
almost 9 years by sadickers
2
answers60
Views
hardwoor flooring
I'm not sure whether this should be here or under floors but anyhow, here are the questions. I am going to be laying Vertical grain bamboo floorin...
almost 9 years by sadickers
2
answers387
Views
out of plumb
I'd go with your second suggestion and attach a filler board on the cabinet. This will also partially hide the gap to the wall and it will be much ...
about 8 years by sadickers
2
answers61
Views
corner molding
I would most likely just make a piece of corner molding out of the same type wood as the bead board. If you wre to look at the piece from the end i...
about 8 years by sadickers
1
answers375
Views
Birch plywood
Most regular Birch plywood is as you said 7 ply, but generally the interior plys are not birch but some other soft wood with just the outside layer...
about 8 years by sadickers
3
answers645
Views
hardwood floors
I'm not sure whether this should be here or under floors but anyhow, here are the questions. I am going to be laying Vertical grain bamboo floorin...
about 8 years by sadickers
0
answers527
Views
remote codes
You might try going to a web site remotecentral.com there are lots of forums there and you can post questions and look over the information that h...
over 8 years by sadickers
3
answers198
Views
outlets
There is a limit on the number of outlets. If I remember corectly I think the NEC calls for non dedicated outlets to use a figure of 180va (volts x...
over 8 years by sadickers
6
answers824
Views
which circuit
It would be easier to just plug in a lamp and the turn off the breakers one at a time until the lamp goes off. The only down side of this will be a...
over 8 years by sadickers
4
answers212
Views
motor wiring
Some motors have the correct wiring information on the motor data plate. THERE WILL BE WIRING CHANGES IN THE MOTOR'S CONNECTION BOX. If in doubt at...
over 8 years by sadickers
4
answers981
Views
1/4" quarter round
On my last home I had the same issue with the cabinets that the contractor didn't scribe to the walls corectly. I finally just bought some oak stoc...
over 8 years by sadickers
1
answers761
Views
nail guns
I have built and am currently building cabinets for my home. I use an 18ga nailgun and a 1/4" staple nailer for attaching the thinner plywood backs...
over 8 years by sadickers
2
answers67
Views
drilling into walls
I certainly couldn't say for sure but I would suspect that if it was built in 1921 that the original walls were lath and plaster. From your questio...
over 8 years by sadickers
1
answers487
Views
3 phase
You got my interest in this up and I spoke with a Fellow I know from work. He is a master electrician and works entirely commercial/industrial stuf...
over 8 years by sadickers
11
answers127
Views
3 phase
Yep, I did some research and Homer you are so right. I am wondering if this is very common? I have heard of the "Wild Leg but never really paid muc...
over 8 years by sadickers
11
answers226
Views
little enos
It would seem as though little Enos has some generator issues. A 3 phase gen set if wound as a 4 wire "Y" configuration should provide 208V leg to ...
over 8 years by sadickers
11
answers826
Views
SDS
I'm not positive but I believe that the SDS drill bits were devoloped by Hilti for their hammer drills. The "slotted drill shaft" sounds a good as ...
over 8 years by sadickers
5
answers69
Views
roof conversion
Let me start by saying that I suspect that I will need an engineers opinion, but just want to throuw this out here to see if anyone has had experie...
over 8 years by pgriz
1
answers244
Views
