Tieger plumbing
Sorry Susan but I doubt if anyone can tell you what could be the problem without going around making sure all the inside valves are open and then t...
COMMUNITY FORUM
What project are you working on now?
Started doing new constuction again,. 50 family homes for middle income
What is your favorite tool?
Sewer and drain cleaning equpment
Recent Posts
about 5 years by Sylvan
7
answers275
Views
Tieger plumbing
No problem Larry
about 5 years by Sylvan
1
answers104
Views
Tieger plumbing
They never do Larry, they want a crash course and then when you go into minor details they get confused with facts..Go figure.
about 5 years by Sylvan
5
answers292
Views
Tieger plumbing
I don't know what code your using but everyone I ever used had an 11/2" tub waste not 11/4 Drainage is by fixture units = 7.48 gallon =1 cubic ...
about 5 years by Sylvan
5
answers527
Views
Tieger plumbing
If you have to ask then call a professional as your asking "What tools" not at least giving us any information saying if it is IPS or copper tubing...
about 5 years by Sylvan
1
answers376
Views
Tieger plumbing
It could be a partial blockage or a blocked vent line either way you may find it cheaper in the long run to hire a licensed professional. Many,m...
about 5 years by Sylvan
1
answers506
Views
Tieger plumbing
Your more then welcome
about 5 years by Sylvan
3
answers150
Views
Tieger plumbing
If your toilet is seeping from a defective fill valve or tank bulb or flapper this will cause condensation on the out side of the pipping and mold ...
about 5 years by Sylvan
3
answers114
Views
Tieger plumbing
Larry, do not take it for granted as many installers figure one valve fits all and even reading Google steam radiator valves some state good for...
about 5 years by Sylvan
8
answers230
Views
Tieger plumbing
Carefully look at the configuration of the valve. Then look at "normal" radiator steam valves angle pattern. Normally steam valves are globe p...
about 5 years by Sylvan
8
answers123
Views
Tieger plumbing
Depending on the Ph of the water if its ok I use type K copper under ground
about 5 years by Sylvan
1
answers137
Views
Tieger plumbing
If the parts are really stripped and the socket tool does not work then you can open the wall a little more and use a basin wrench to remove the nu...
about 5 years by Sylvan
3
answers1000
Views
Tieger plumbing
That would depend on the code and piping in general should be protected from coming in direct contact with cement
about 5 years by Sylvan
1
answers676
Views
Tieger plumbing
The system is hot water so you better make sure you drain down the system completely before loosening the union Ell or valve and there will be real...
about 5 years by Sylvan
8
answers193
Views
Tieger plumbing
Hi Bill, That is why I make my own heat sink by installing the cold water feed 27" down then bring it up to the heater to prevent stratification of...
about 5 years by Sylvan
3
answers384
Views
Tieger plumbing
Someone forgot to install a dielectric fitting by to prevent electrolytic action between ferrous and non ferrous metals thus the mineral deposits ...
about 5 years by Sylvan
3
answers201
Views
Tieger plumbing
Yes I did that several times On demand has no provisions for water to return to the source thus your losing a lot of water was the water that ...
about 5 years by Sylvan
2
answers539
Views
Tieger plumbing
Why install a new one if you had paid a plumber to install it in the fist place have him /her come back and make things right NO CHARGE....
about 5 years by Sylvan
10
answers833
Views
Tieger plumbing
Did you ask for a licensed plumber? Many times I go behind a franchise stumble bum the worst possible non trained person sent out in the field a...
about 5 years by Sylvan
10
answers243
Views
Tieger plumbing
I personally would have replaced the Douglas valve and in case of Eljer the outlet is china so possibly roughing up the surface and then drying it...
about 5 years by Sylvan
10
answers521
Views
