Grinding Wheel for Aluminum Flat Stock
If you have a 4 in or hand grinder, you can use a 80 grit alum oxide or ceramic coat disc or a flap disc. You can also use a 4 in x .90 cutting di...
COMMUNITY FORUM
Recent Posts
over 9 years by toolcen2
3
answers866
Views
Strange odor coming from vents when furnace operates
I would suggest that you check the heat chamber very closely, there may be a hairline crack, and this could be carbon monoxixe gas fumes. also, ch...
over 9 years by toolcen2
6
answers352
Views
Shaper/Moulder
This is a wonderful tool sounds like you have lots of room. If consedering this item, I would get at a 1 1/2 or larger with reverse. preferably Del...
over 9 years by toolcen2
1
answers896
Views
Pellet stove heat output questions
I have a harmon pellet stove about the same size as your unit. I have 2800 sq ft, and this is the only heat source I have. The first thing I would ...
over 9 years by toolcen2
2
answers643
Views
Newbie Drill/Driver Question
There is a problem with your chuck assembly. If this is a dewalt drill, 1/2 inch, you can repalce this with a ratcheting chuck assembly, and stop t...
over 9 years by toolcen2
5
answers108
Views
Laser Tape Measures
the following are the specs on an american model made by irwin tool.calculates square foot and cubic footaccurate +/- 4 inch at 50 ftrange 2 ft t...
over 9 years by toolcen2
3
answers707
Views
Cool Blocks
I have this item, they are non metallic and come 4 per pk. upper and lower stock no is 708719.
over 9 years by toolcen2
4
answers210
Views
Laser Tape Measures
I have these in stock, I will get specs and send you information
over 9 years by toolcen2
3
answers612
Views
Cool Blocks
Do you need upper and lower.I will see if have these in stock. will reply on Monday
over 9 years by toolcen2
4
answers114
Views
Wood pellet stoves...pros and cons?
I have a wood pellet stove as the only source of heat. I have a 28oo sq ft house, L shaped. I have had this source for over 5 years. odroless,does...
over 9 years by toolcen2
1
answers600
Views
Torx-type screwdrivers?
if you know what sizes you need, let me know, and i will send you the cost factor. i have these in sets also . They dont come in screwdriver series...
over 9 years by toolcen2
4
answers639
Views
Small Vac For Drywall Dust
Dewalt has introduced into the line a new 12V-18V cordless vacum cleaner. It is full portable and shop type use. model is dwdc500 at 99.00 see my...
over 9 years by toolcen2
1
answers802
Views
Weeping Willow tree
I feel you may have a major problem in the future. I had same several years ago, and the tree was aprox 50 to 75 feet away. any type willow has a t...
over 9 years by toolcen2
1
answers861
Views
Low pressure after replacing water heater.
Check the pop off valve, on top of heater, and make sure not open position or stuck open.If so, all water is just going out valve .
over 9 years by toolcen2
2
answers975
Views
Searching for 5 7/8" Blades for Skilsaw
This model of saw has been discontinued for many years. Some companies have a resharpen program, and there are a few of these left. This model of ...
over 9 years by toolcen2
1
answers707
Views
Drill Bits Steel vs Titanium
Titanimu bits are an inexxpensive bits with a sprayed on powder coating and heated to 650 degree.They only run cooler, and do not cut as well as a ...
over 9 years by toolcen2
4
answers772
Views
Doing something with plywood cabinets?
I HAVE DID SEVERAL JOBS OF YOUR TYPE BY FIRST REMOVING ALL THE DOORS. LOOK AT THE FRAMEWORK, AND FIGURE THE APROX AMOUNT OF WOOD PRODUCT YOU NEED. ...
over 9 years by toolcen2
1
answers347
Views
How to prevent screw heads from stripping?
IN MOST CASES, IF YOU ARE USING A CORDLESS DRILL, THIS IS THE INCORRECT TOOL FOR DRIVING DECKING SCREWS. YOU NEED TO CHANGE TO A DECKING GUN WHICH ...
over 9 years by toolcen2
6
answers872
Views
Hydraulic lifting mechanism for table
I have a hydraulic table lift that is aprox 24 x 30 which lifts capacity of aprox 800 lbs. you could simply add the top size you prefer to make a ...
over 9 years by toolcen2
4
answers658
Views
Craftsman Compressor
EVERYTHING WILL BE FINE, IF YOU WANT TO EXCHANGE THE UNIT, NOW WILL BE THE TIME. I WOULD SUGGEST THAT YOU TRADE TO A OIL TYPE UNIT IN THIS CAPACITY...
over 9 years by toolcen2
3
answers197
Views
