Versatile tools
k2, Good point about the class. I am in complete agreement with you on that. Most Community Colleges offer Woodworking classes. U.S.M.C. Semper ...
COMMUNITY FORUM
Recent Posts
almost 8 years by tperez
3
answers40
Views
Lighting the County
Mikee, Are there many accidents on this road or dangerous curves and/or warning signs? If so I would check with your DMV office and get the accide...
almost 8 years by tperez
6
answers941
Views
Thank You
Jim D, Thanks for the heads up on the H.D. As luck would have it (The wifes luck that is.) I have a rather large project in the works. I believe I...
almost 8 years by tperez
2
answers661
Views
most versatile tool
rjpbob, The most versatile tool in any wood shop is the Router (I prefer the plunge type) and table. This tool with the proper bit can do almost a...
almost 9 years by tperez
3
answers260
Views
I'll jump in
Journeyman Electrician for ten years in commercial and residential service. Installing,troubleshooting,and repairing electrical systems as well as ...
almost 9 years by tperez
11
answers923
Views
Bar top
Gjackson, I believe you are referring to the clear acrylic coatings on tables that get poured on and then dry clear. If this is so then around the...
almost 9 years by tperez
1
answers198
Views
Rusty tools
You can get the rust off and apply a thin coat of Johnson Paste Wax. This will also keep the metal somewhat lubricated. Stay away from silicone bas...
about 8 years by tperez
1
answers819
Views
Drills
ztools, Forgive me if I get this wrong but I don't know exactly what you are asking. If your husband needs a drill and is not a professional user ...
about 8 years by tperez
1
answers627
Views
Painters Fault
Mistressell is probably correct. This sounds like a three way to me. Around these parts if the painters took it down and can't put it back right th...
about 8 years by tperez
14
answers657
Views
Garage Wiring
loosegroove, Running sheathed electrical cable will be fine for your Garage. Just do what you have planned with the box and you should be fine for...
about 8 years by tperez
7
answers436
Views
warped tops
rjw138, This is not good. I can see why you would not want to replace this top. Being an antique and all. My suggestion is to find a high pressure...
about 8 years by tperez
1
answers982
Views
support
MistressEll, You are correct in that some houses are not of the three wire systems. Since the area of the clearance is greater than the fixture t...
about 8 years by tperez
10
answers817
Views
recess cans
I'm not sure what brand of cans you are installing but I have yet to install a recess can without a heat sensor. You may wish to find a different m...
about 8 years by tperez
10
answers785
Views
ansi ratings
mistressell, What you are looking for is the high impact rating. This should have an (AOSZ87+) marking on it for goggles and faceshields. For spe...
about 8 years by tperez
3
answers696
Views
Plastic box
stretchad, Yes, you will need a Blue Carlon Retrofit Box, a drywall saw, a philip screwdriver and a chase nipple if your fixture calls for it. The...
about 8 years by tperez
1
answers495
Views
Kitchen lighting
susanf, What is your definition of close to the cabinets? Recess cans are generally placed 18-24 inches away from the wall or other objects. This ...
about 8 years by tperez
2
answers633
Views
Recessed Lights
handygirl, I applaud you for your effort to learn. I further applaud your reading the manufacturers instructions. You will get two schools of thou...
about 8 years by tperez
10
answers373
Views
Ink stains
Try some rubbing alcohol with a rag. Nail polish is an Acetate and will destroy the finish on the veneer (assuming it has some). U.S.M.C. Semper ...
about 8 years by tperez
2
answers630
Views
burned table
fmattheg, The existing varnish will need to be stripped off the table to see if the burn is only discoloration of the varnish or the wood. The bur...
about 8 years by tperez
2
answers619
Views
Cutting Letters
I would trace out my letters on the stock and cut them with a scroll saw just outside the lines and sand them to the line for a smooth finished loo...
about 8 years by tperez
1
answers172
Views
