Craftsman 10" Table Saw Motor Problems
I have owned a Craftsman 10" table saw for almost 15 years. The motor is rated at 1.5 HP (sold as 3 Hp peak) 120volts 13amps. The problem is recently wehn i start...
Latest Discussions: TOOLS & WORKSHOP
Craftsman table saw motor
I have a craftsman table saw with motor model number 820030 that starts really slow kicks out the breaker. I changed the start capacitor and had the run capacitor...
0
answersupdated 7 months ago by BV019275
Sandpaper for Craftsman belt sander model # 207.22301
We have recently obtain an old Craftsman Sander but are unable to find sandpaper for it--can anyone help us?
3
answersupdated 7 months ago by BV019253
Manuals for 351.22676, 319.190420, and 315.17260
Looking for manuals for: Sears Craftsman Sander/Grinder 351.22676 Sears Craftsman Grinder 319.190420 and Sears Craftsman (Scroller) Scroll Saw 315.17260
2
answersupdated 7 months ago by BV019181
granite bridge saw
bridge saw USA, Inc. is a USA-based P.B MArble company that offers high-quality stone equipment matched with the fastest and best service in California City. P.B ...
0
answersupdated 8 months ago by BV019054
Rear Mounting Sockets for Drawer Slides
Has anyone heard of a company called Scheirich Cabinetry? One of the rear mounting sockets for a drawer slide broke. The socket is of a peculiar design as it is h...
46
answersupdated 8 months ago by BV019052
Tool shop air commplrlessor parts
I have a tool shop 3 hp 6 gallon air compressor that I need a pistone seal kit for........any ideas? ????
0
answersupdated 8 months ago by BV019033
Rockwell/Delta 34-600 Table Saw
Need a parts manual and owners manual for a Rockwell/Delta 34-600 9" table saw. In fact any information anyone has on this saw I would appreciate. I have owned...
31
answersupdated 8 months ago by BV019021
Particle board under laminate
I wanted to stain a table I got from my mother in law, but it had a laminate top. I assumed it was wood underneath however, because the sides were wood. I steamed...
0
answersupdated 8 months ago by BV019020
Craftsman Belt Sander Model No. 315.11721
I recently inherited a Craftsman Belt Sander Model No. 315.11721, and I went to use it today but realized that the belt needed changed. Only one problem, I can't...
71
answersupdated 8 months ago by BV019004
Wards Powr_Kraft Table Saw
I'm looking for an owner's manual or parts list for a Wards Powr_Kraft table saw model number 94FD2260B. I know it was made by Duro - Metal Products. I have f...
1
answersupdated 8 months ago by BV018990
Old CraftsMan Radial Arm Saw
I have a Craftsman Model #11323100 Radial Arm saw in very good condition that I have had for years & does an excellent job for what it is intended. However, I...
3
answersupdated 8 months ago by BV018962
craftsman jointer m#102-05600 6inch
Dose anyone know where parts might be found for this jointer
0
answersupdated 9 months ago by BV018869
Craftsman table saw 113.22411
I have my Pop's old craftsman 10" table saw model 113.22411 I am in need of some obsolete parts the most important being the table top insert part #6151. I have ...
1
answersupdated 9 months ago by BV018803
Old Craftsman direct drive 12" table saw.
I have an old Craftsman 12" direct drive tablesaw (blade mounted on the motor) and need a manual. There is no indication of a model number anywhere other than on ...
3
answersupdated 9 months ago by BV018784
Backstop 47222 for old Craftsman belt/disc sander
I am looking for a backstop for a Craftsman 113.225930 combo belt/disc sander.The part number for the backstop is 47222.Sears Parts direct is permanently out of s...
0
answersupdated 10 months ago by BV018695
Craftsman 113.241730 replacement motor
the motor is no longer available, any suggestions on a substitute?
0
answersupdated 10 months ago by BV018684
Craftsman 6 1/8 inch planer 113232200
I need a F Dovetail #21218 a plate #21812, and a spacer #21422. If anyone has those parts please contact me. campers9@yahoo.com
0
answersupdated 10 months ago by BV018668
Re: Shopmate 5200 radial arm saw
I have been overhauling my machine because the arm refused to swing from left right. It was siezed. In order to gain access the the mechanism I had to remove the ...
0
answersupdated 10 months ago by herbenu
Shopmate 5200 radial arm saw
Regarding the question of stiff rise and fall on the column, look underneath the column base and you will see a worm drive. Try greasing it. Also, spray WD40 lubr...
0
answersupdated 10 months ago by herbenu
