Bake burner flame?
** BROIL setting & CLEAN setting oven turns on as expected ** Do both broil AND bake burners ignite when on clean? You're not maybe just seeing the broil b...
Discussion History
Lint brush
** We believe there is a lint build-up on the inside duct (where the pull-out lint trap is). How do you clean out internal lint build up? ** There are long han...
1
answersupdated almost 10 years ago by DanO
GE round style detergent dispenser
** [GE dishwasher model GSD5920D00BB] soap cup isn't opening. ** The dispenser on that model is mechanical. You can read a bit about it under "Round style disp...
2
answersupdated almost 10 years ago by DanO
Transmission problem?
** starts to spin real slow and is pumping out water ** Your washer model uses a 'neutral drain' transmission. It should first drain *without spinning* and the...
2
answersupdated almost 10 years ago by DanO
Clarification needed
** burner turns on ... but regular oven will not turn on. ** Which burner are you referring to? And by "turns on" do you mean ignites into a flame? ** al...
7
answersupdated almost 10 years ago by DanO
Lid switch problem?
** when you close the lid you need to push down on it to engage the lid switch. ** That sounds like a problem with the lid switch mechanism (see the following ...
2
answersupdated almost 10 years ago by DanO
Tried new filter?
** The water tasted funny. GE says it is my copper pipe that runs the water to the fridge and needs to be replaced. ** Is its water supply filtered by a RO fil...
2
answersupdated almost 10 years ago by DanO
Results?
So how did the results of that test turn out? Dan O.
9
answersupdated almost 10 years ago by DanO
repeat
** I remember reading something about the heating cycle but though it "the coil" was on for several minutes before going off. ** That is usually true but witho...
9
answersupdated almost 10 years ago by DanO
Not convinced vent is not the problem
** 2 story house... the builder installed a rigid vent pipe (25 - 30 feet at most) in the interior wall 1st floor laundry room up through the 2nd floor and wall a...
9
answersupdated almost 10 years ago by DanO
Venting checked?
** Could it be a thermostat or thermistor that's bad? ** Either could be a possibility but I would suggest you start with the simple things first, the main one...
9
answersupdated almost 10 years ago by DanO
Lid switch problem?
** washer won't drain ** Is the motor running at that time? Does the timer advance through the rest of the cycle if left alone or does it stop right at that...
3
answersupdated almost 10 years ago by DanO
Lid switch problem?
** I used a screwdriver to activate the switch and then the washer proceeded through the rest of the cycles as usual. The plastic piece on the bottom of the lid ...
2
answersupdated almost 10 years ago by DanO
Call for service
** What should I do? ** If you can't look into it yourself I suggest you call for service before it gets any worse and/or leads to further damage of the machin...
8
answersupdated almost 10 years ago by DanO
From which component?
Someone will need to pinpoint the actual origin of the sound. Maybe the transmission, maybe the clutch above the transmission or maybe something just caught betwe...
4
answersupdated almost 10 years ago by DanO
Pump problem?
** it is not pumping out the water correctly, could this mean something is just caught in the pump? ** Very possible, yes. - Direct Drive Washer Water Pump...
4
answersupdated almost 10 years ago by DanO
Only one available
** there are 2 diff kinds of part old/new can you use newer on both? ** The current design of motor coupler is all that is available and replaces all previous ...
6
answersupdated almost 10 years ago by DanO
no option
There is no option to move a post I'm afraid. JFYI Dan O.
3
answersupdated almost 10 years ago by DanO
Better forum?
A better forum for your ad (and any others about selling) might be Bob's - Buy, Trade, or Sell forum. LINK > www.bobvila.com/BBS/Buy_Trade_or_Sell-1-C58.ht...
3
answersupdated almost 10 years ago by DanO
Model number incomplete
** Model # 91554210 ** That model number is incomplete. It is missing the 3-digit manufacturer's prefix. Once you get the complete information you can use the ...
1
answersupdated almost 10 years ago by DanO
