Kitchen Sink Installation Problem
I recently completed a granite tile countertop project and I now have a problem trying to install a new drop in kitchen sink into the countertop. The total ...
Discussion History
Soldering Problem
When I soldering the solder seems to clump on the pipe instead of smoothly running aroud the outside of the pipe. I alway heat the fitting and apply the solder t...
0
answersupdated almost 14 years ago by Paul in Toronto
Bathroom Light
Is there a standard height for a light over a bathroom vanity?
1
answersupdated about 14 years ago by jackofallmasterof1
Shower Faucet
Hey guys thanks for your opinion. To tell you the truth I was already leaning towards Delta and this just confirmed it. Jack who are things in Myrtle Beach? ...
2
answersupdated about 14 years ago by Paul in Toronto
Standard Height
Is there a standard height for mounting a light over a bathroom vanity?
0
answersupdated about 14 years ago by Paul in Toronto
New Shower Faucet
I will be replacing my shower faucet very shortly and I'm planning on buying either a Delta or Moen faucet. I'm interested in any feedback that you can offer...
2
answersupdated about 14 years ago by Paul in Toronto
Stickers
I've had good luck removing stickers with a product called Goo Gone.
6
answersupdated over 14 years ago by Paul in Toronto
Ryley
Has anyone ever found a website for Bob Ryley's company?
4
answersupdated over 14 years ago by Paul in Toronto
Question about Bob and Sears
I also assume that Bob no longer has any kind of association with Sears. Last fall (2005) the name of his show was shortened to Bob Vila from Home Again with Bob ...
3
answersupdated over 14 years ago by Paul in Toronto
Split GFCI Receptacle ?
Is it possible to split a single GFCI receptacle and have each half supplied by it's own circut? If it is possible, how is this done as I don't see a breakab...
2
answersupdated over 15 years ago by Billhart
Bosch Router Combo Kit
I'm thinking of buying the Bosch 1617 router combo kit (router motor with a fixed base and a plunge base) and I'm looking for some feedback from anyone who owns o...
0
answersupdated over 15 years ago by Paul in Toronto
MDF Beadboard in Bathroom
I would like to use a MDF Beadboard(tongue & groove)in my bathroom. How well will it hold up in a high humidity location?
1
answersupdated about 16 years ago by Altereagle
Shed Wiring
I planned on running sheathed electrical cable from the breaker panel to the outside of the house and then using UF for the exterior portion. I'm just not su...
3
answersupdated over 16 years ago by Paul in Toronto
New Circut to Shed
I am planning on running a new underground circut to a detached shed. The circut (120 volts / 15 amps) will power one receptacle and one overhead light. I hav...
3
answersupdated over 16 years ago by joed
tub nipple
I definitely want to change the nipple. I have never heard of an internal pipe wrench. How do they work and where are they available?
4
answersupdated almost 17 years ago by Paul in Toronto
Tub Spout Nipple
I need to replace the existing tub spout nipple with one that is a half inch shorter in length. How do I remove the old one and more importantly install the ne...
4
answersupdated almost 17 years ago by erik peterson
Interior doors won't stay open
Try removing the bottom hinge pin and put a small bend in it (lay the pin on a concrete surface and tap the pin with a hammer). You don't want too much of a bend...
4
answersupdated over 17 years ago by Paul in Toronto
Concrete measuring...
Ready-mix companies sell concrete in cubic yards not square yards as you mentioned in your post.To determine how many cubic yards you require you must first deter...
1
answersupdated almost 18 years ago by Paul in Toronto
Episode - May 25, 2003
You didn't mention what channel you were watching but I'm guessing it was TLC. TLC broadcasts Home Again every Sunday morning from 10:00am to 12:00pm.The episode...
1
answersupdated almost 18 years ago by Paul in Toronto
need quick ans. re. roof repair
Provided that the plywood is the same thickness as the old 1x6's I wouldn't worry about it.
2
answersupdated about 18 years ago by Paul in Toronto
