deflection & glue
Adhesive isn't necessary. If you use it though, make it full spread. Span has nothing to do with the size of the room your tiling. It's unsupporte...
COMMUNITY FORUM
scuttlebuttrp
Member since 08/29/07Recent Posts
about 10 years by scuttlebuttrp
6
answers1056
Views
inadequate joists
Can't speak about the wood, but 1/2" ply won't cut it for tile. What is the length of the span of the joists? If they can pass Deflection, then y...
about 10 years by scuttlebuttrp
6
answers542
Views
Dry loc
I've never seen or heard of Dry Loc. Apparently it's a painters thing. However I do do a lot of tile. I have yet to see a bag of thinset that says ...
over 10 years by scuttlebuttrp
2
answers1112
Views
Cement
You would need a bondcoat between the two. What exactly are you trying to accomplish?
over 10 years by scuttlebuttrp
2
answers249
Views
removing tile
Cut out the grout with a grout saw.You can find them at any home improvement store. A razor knife might also work if the grout is weak enough. Put...
over 10 years by scuttlebuttrp
3
answers257
Views
Foreign words.
Monococcion=Single fired. Tile is manufactured in one firing of the kiln. 33x33= Tile size in millimeters. About a 13"x13"? The other words s...
over 10 years by scuttlebuttrp
2
answers625
Views
Tile depth
They make some cool boxes that have screws on the side to change the depth of the box. But for normal boxes; we usually cut as tight as possible to...
over 10 years by scuttlebuttrp
1
answers346
Views
unlevel floor
The floor is not supposed to be out more tha 1/4" in ten feet. That's a flat plane. Level is something else. Level is better but sometimes unacheiv...
over 10 years by scuttlebuttrp
2
answers156
Views
tile on concrete
First put a little water on the floor.If it soaks in then the floor is not sealed and your good. If it sits there, then it's sealed and you have a...
over 10 years by scuttlebuttrp
1
answers1170
Views
polishing
They need to be wetsanded with very high grit sandpaper or disks. Best done before installation.
over 10 years by scuttlebuttrp
1
answers894
Views
floor condition
Your deflection on that floor should be fine for ceramic. It falls short for natural stone. If you have SYP joists; and those 1x6's are still in g...
over 10 years by scuttlebuttrp
4
answers915
Views
subfloor
Definitely remove the particleboard. If the 1x6's are in good shape and you have enough height. Install 3/4" ply perpindicular to the joists. By t...
over 10 years by scuttlebuttrp
4
answers159
Views
wall height
84"-90" is normal for height. Listello is typically eye level; around 60". But it's your shower so do what you think looks good.
over 10 years by scuttlebuttrp
1
answers168
Views
transition
This is a personal asthetic issue. Do what you think looks good. I like the stone mosaic idea. Or you could use one large piece of wood that is as ...
over 10 years by scuttlebuttrp
1
answers796
Views
glue
Just trust the carpet guy. There's nothing wrong with what he's proposing. I've done thousands of yards of carpet just like that.
over 10 years by scuttlebuttrp
1
answers266
Views
doubtful
I don't think the durock would provide enough strength to hold the weight of the concrete.
over 10 years by scuttlebuttrp
1
answers983
Views
hole
Depends on the tile but I've always liked using a side grinder with a diamond blade.
over 10 years by scuttlebuttrp
1
answers1134
Views
Tenting
It's called tenting and is usually caused by the tile being cut too tightly to the walls or the perimeter has been grouted against the base board. ...
over 10 years by scuttlebuttrp
1
answers910
Views
slate/ exterior question.
Need more info on this one; go here to get help. http://www.johnbridge.com/vbulletin/index.php?referrerid=27552
over 10 years by scuttlebuttrp
1
answers291
Views
sealer
If it says that it's a sealwer, no you shouldn't need anything else. Water is ph neutral. You can also buy their fancy ph neutral cleaner, but wa...
over 10 years by scuttlebuttrp
1
answers835
Views
