Latest Discussions : Tools & Workshop

sadickers

08:48AM | 05/30/04
Member Since: 02/20/04
52 lifetime posts
Well I did a little research and ran into a dead end on the ***** web site. They just say Motor unavailable (P/N 62618). I have had two ***** 10" tablesaws first one for 30+ years and now have a new one. Both saws had motors rated for 115/230 Volts 3450RPM. The Pulley on the motor is 2" dia. (You might want to measure the diameter of the pulley on the blade end and compute the RPM ratio so that you don't exceed the max blade RPM). As for the HP rating on the motor The first saw I had was equipped with a 1 1/2 HP motor and wasn't really up to the task if I was doing serious ripping. My new one has a 3 HP motor and works great. Anyhow the HP rating can pretty much be what you want in the range of about 1-3 HP. If you opt, I would, for the 3 HP motor just be sure the circuit you plan on plugging into can handle the load. Also be sure the motor base will fit on the saws motor mounting base. (I have configured the motor to run off a dedicated 230 Volt circuit. wiring diagram is on the motor housing).

Hope the above is of help.

Steve

JFOSTER

06:33AM | 06/07/04
Member Since: 05/26/04
6 lifetime posts
Thank you. I went back to the guy I bought the table from and he had the motor.

Everything you said was right and if I hadn't of gotten the old motor I could have gotten a new one based on your info. It is a 1 horse so I will see if it fits my needs. I suppose I can always upgrade to the 3 horse knowing what I know now.

Just incase someone else finds this thread I will type in the motor specs for 113.298031.

MODEL: 113.12171 CAT: 1217 HP:1

RMP 3450 HZ:60 PHASE: 1 Volts: 115

AMPS: 14 UNSUL. CLASSS: A S.F.: 1.0

S.F.A: 14 CODE: K AMB: 40C FRAME: G56Z

BRGS: SLEEVE TIME RATING: CONT.

MFG MODEL: KS55FN-1047 MFG NO: 9793

CAPACITOR START A.C. MOTOR

Thanks for the resourse.

James

carl21l

05:59PM | 06/14/04
Member Since: 03/21/04
171 lifetime posts
all craftsman tools that have a 113 code are made by Emerson Electric. their technical support No. is 1-800 474-3443 they often have parts that ***** no longer stock because the same parts are interchangeable with Ridged parts. example. I bought a craftsman miter gauge clamp for table saw at a yard sale, it was an exact copy of the one that ********** had in stock except the grip is red on Ridged and black on Craftsman. also Ridged parts are cheaper than those from ***** parts.

Carl

idtemm

05:06PM | 08/04/07
Member Since: 08/03/07
2 lifetime posts
I have an small old table saw model number 113.19053 and I can't find any information on it. Does anyone know of a website that might have some information?

Thanks!

DSTEELE1

04:47PM | 08/06/07
Member Since: 01/21/05
25 lifetime posts
Try the old woodworking machines

(owwm ) website.

idtemm

03:50PM | 08/08/07
Member Since: 08/03/07
2 lifetime posts
Thanks for the response! I will check that website out.

nas1rami

05:46AM | 10/20/07
Member Since: 10/19/07
1 lifetime posts
here is a link to a motor listed on eBay 4 ur saw. Check it out.

http://cgi.ebay.com/SEARS-CRAFTSMAN-1-HP-3450-RPM-ELECTRIC-MOTOR-TABLE-SAW_W0QQitemZ180166011559QQihZ008QQcategoryZ20789QQcmdZViewItem

tryme43123

09:19PM | 01/09/09
Member Since: 01/09/09
2 lifetime posts
I have the exact table saw you mentioned in your post (113.298031). I bought this saw 29 years ago brand new. I have all the specs from my motor (original) that you would need. The saw is in its original condition except that I re-painted the table extenions, installed a dust collection port and a Delta T-2 self-squaring fence (which I really love). You may email me at: tryme43123@yahoo.com to obtain all the info you need to know from my motor.

Bill

tryme43123

daddyshelper78

09:56AM | 01/12/09
Member Since: 01/11/09
1 lifetime posts
my father has this table saw. I can remember being a little girl helping him make things in his shed. (Really more playing in the saw dust) He is needing the number of the capacitor to make his 1hp motor work again. It got all rusty from sitting around and not being used. He is wanting to get it working again so that he can build his grand-daughter a bed and toy box. If someone could help me out please. My email is: longhairlonglegs@hotmail.com

Thank You

tryme43123

12:32PM | 01/12/09
Member Since: 01/09/09
2 lifetime posts
BRAND: MALLORY USA, 216-259MFD 110VAC, C10-109234B-170, 60 CYCLE, 235-8010K-01

tryme43123

Redwine

04:21PM | 01/13/09
Member Since: 01/12/09
1 lifetime posts
I have owned this table saw for 30 years. I recently have been overhauling it and discovered the motor would not start. I pulled the capacitor and here is the information you have requested..

Capacitor manufacturer..Mallory

216-259 Mfd, 110VAC

C10-109234B-170

235-7616K-05

$8.35 at the electronics parts store

Not sure what the long numbers were. I went to the parts counter at the local electrical supply house and gave them the manufacturer and the 216-259 Mfd (Micro Farads, measure of capacitance) and they gave me the part. Hope this helps

sdav01

08:42AM | 12/01/09
Member Since: 11/29/09
1 lifetime posts
I have a craftsman table saw,part#113.298030.It has no pulleys.Does anyone Know What dia.they are supposed to be? Iknow that the shaft sizes are 5/8",and the motor rpm is 3450.but need pulley sizes for proper ratio.Anybody anywhere know?

Thanx, Sdav

doug seibert

10:12AM | 12/01/09
Member Since: 08/10/02
842 lifetime posts
The exploded view/parts list can be found by searching at:

http://www.searspartsdirect.com

Shows pulley(s) #44 twice.......2 1/2" diameter....

replacement/substitution still available from Sears Parts Direct

"......measure Once.....cut Twice....

throw that one away and cut a new one...."

tetapehta

09:29PM | 08/03/10
Member Since: 08/03/10
2 lifetime posts
Today I bought from craaiglist an electric motor (1 HP, 110 V, 3450 RPM with two shafts). I plan to make out of it a buffing machine. The seller told me that the motor runs at 3450 RPM. When the motor arrived to my house, I've checked the label on it. The label was severely damaged. I could not read anything except the manufacturer ( CRAFTSMAN) and the model 113.12171).

So, I googled "craftsman 113.12171" and found the post, posted back in 2004 by gentleman JFOSTER.

Among other things he said:

Just in case someone else finds this thread I will type in the motor specs for 113.298031.

His prophecy became reality today. HE MADE MY DAY.

Mr. JFOSTER, if you read this, rest assured, I AM REALLY THANKFUL for the motor data, you typed into the internet collective knowledge base.

Thanks again

Igor

P.S. I joined this forum just to be able to post this message


Post a reply as Anonymous

Photo must be in JPG, GIF or PNG format and less than 5MB.

Reply choose button

Anonymous

Post new button or Login button
Register