How To: Patch Drywall

If you're setting out to patch drywall, whether the problem at hand is a few nail holes or a large gash, these simple tips can help you restore a smooth surface ready for paint.

By Bob Vila | Updated Dec 8, 2020 12:12 PM

We may earn revenue from the products available on this page and participate in affiliate programs.

How to Patch Drywall

Photo: shutterstock.com

Sooner or later, most of us need to patch drywall, whether for purely cosmetic reasons—filling nail holes, for example—or for comfort or safety—say, a hole has left wiring exposed. Although accomplishing the latter requires a greater investment of time, rest assured that a do-it-yourself solution exists, no matter the scale of the repair. Read on for guidelines for patching drywall in small-, medium-, and large-size projects.

Patching a Small Area

TOOLS AND MATERIALS Available on Amazon
Sandpaper
Spackling paste
Putty knife

The smaller the hole, the easier it is to patch. Start the process by sanding the area smooth. Next, load a bit of spackling paste onto your putty knife and apply the product directly to the hole. Work in enough of the paste so that it leaves a small mound over the hole, then press the flat side of the knife firmly against the mound in order to flatten it. Finally, swipe the blade in a broad motion across the repaired area, leaving the filled-in hole perfectly level with the finished drywall. Allow the spackling sufficient time to dry. Dry times vary, so refer to the manufacturer’s instructions for an accurate estimate. Sand lightly when dry.

Get a pro to do it for you
Receive free, no-commitment project estimates from licensed drywall installation and repair pros near you.
+

Patching a MediumSize Area

TOOLS AND MATERIALS Available on Amazon
Sandpaper
Putty knife
Joint compound
Drywall mesh tape

If you want to patch a somewhat larger hole—an area with a diameter of one or two inches—the process becomes slightly more complicated, if only because it involves a material you might not have on hand: mesh tape. (You can buy mesh tape either as a roll or as a precut square.) After sanding the area to be patched, completely cover it with mesh. This now becomes the base to which you’ll add joint compound, a product that goes on like spackling paste but achieves a stronger result. As you spread the joint compound, pay special attention to the seams where the mesh tape meets the surrounding drywall. Once you can no longer see the tape, use the putty knife to flatten the mounded joint compound, then scrape the surface in wide, smooth side-to-side movements that create an even finish. Finally, allow the joint compound to dry for about eight hours—consult the manufacturer’s directions—before sanding and repainting the wall.

How to Patch Drywall - Large Hole

Photo: shutterstock.com

Patching a Large Area

TOOLS AND MATERIALS Available on Amazon
– Drywall panel
– Utility knife
– Drywall saw
– Drywall screws
– Screwdriver
– Drywall mesh tape
Putty knife
Joint compound
– Sandpaper

A larger patch involves a commensurately greater commitment of time and effort to complete. In fact, the patching process here is not very different from the one that was used to install your drywall in the first place. Begin by using a drywall saw to cut evenly around the problem area. You should be left with a hole that’s rectangular in shape; use a utility knife to clean up the edges, if necessary. If possible—and to do this, you may need to make the hole larger than seems strictly necessary—make your hole big enough to expose one of the wall studs. Failing that, you’ll need to run a wooden member horizontally between the two closest studs. Why? You’re going to fill the hole in the wall with a piece of new drywall, and that piece needs a surface to which it can be securely attached.

Next, use a drywall saw to cut out a section of the drywall panel you’ve procured either from the surplus in your garage or from the aisles of your local home center. Measure and cut carefully, as the piece must fit perfectly into the rectangle you’ve cut in the wall. Once you’re certain that you’ve got a snug fit, use drywall screws to attach the new drywall to the stud (or horizontal member).

With the drywall patch firmly in place, apply mesh tape over all the seams between the patch and the existing drywall. Then load up your putty knife with joint compound and proceed to cover the mesh completely. (Don’t forget to smooth compound over the drywall screws, too.) Use the blade of the putty knife to flatten out the compound in any spots where it’s mounded, then scrape across the seams in wide strokes, either side-to-side or top-to-bottom, depending on the orientation of the mesh. Allow the compound to dry for about eight hours before you begin the final stage: sanding the patched area and repainting the freshly repaired drywall.

Get a pro to do it for you
Receive free, no-commitment project estimates from licensed drywall installation and repair pros near you.
+