12:56PM | 05/14/05
Member Since: 05/13/05
6 lifetime posts
Hi All!

I'm adding ventilation to our 55-year-old ranch style home. The entire roof is a hip-roof (no gables), with about 300 feet of gutter attached to sealed soffits that drop down about a foot below the top of the 9" brick exterior wall.

There are two small "gable" type vents at each end of the main roof peak, and no soffit venting. Moisture wasn't really a problem until I started going into the attic to work on the house wiring, but the heat up there in the summer has now come to my attention. My guess is that it gets up to at least 150 degrees in the attic during peak August sun. There's currently about 16" of 1970's vintage blown-in insulation up there, but I've been moving it around a bit. I figure that as long as I'm dealing with the heat situation, I'll be stopping any future moisture issues. Right now, I'm working at the top of the exterior walls, but I'll be adding soffit/ridge vents at a later time when I do some more math.

I've got a few pictures of what I'm doing at

Each rafter is plugged at the outside of the exterior wall with a 2x6, nailed from the soffit side (remember that this house has 300' of SEALED soffit). What I'm doing from the attic side is using a Speedbore bit with an extension and a Sawzall to cut a 1" high slit in the 2x6 where it meets the roof decking. I'm then notching the ProVent rafter baffles to get a better seal against the 2x6.

My question is this:

How concerned should I be about getting a perfect seal here?

Spray foam does not stick to overhead surfaces very well, and I'm concerned about it expanding into the slit in the 2x6. I've also thought about craming some fiberglass batt insulation into the area where the baffle meets the 2x6, and then inserting more uncompressed fiberglass insulation until I reach the inside top of the exterior wall (resulting in about R-15). I've also thought of making rigid foam insulation cutouts that would fill basically cover the inside of the 2x6 (ADOVent makes cardboard cutouts, but not to fit the 16" on-center of my rafters).

Or should I not really be concerned about air leaks at all, and just spread the cellulose insulation all the way to the 2x6 and top off the attic to 16" when I'm done?

As a side note: baffles are useless at the inside corners of this hip roof (almost 3 feet each way from the corners). Should I fill in those areas to the roof decking, or should I just cover the attic floor and leave an air space between the cellulose insulation and the roof?

Thanks in advance for your help.



08:51PM | 08/01/05
Member Since: 11/27/04
172 lifetime posts
venting is venting and the more the long as you can get at it. i always use full soffit venting as it allow the whole lower roof area to breath.

only concerns are blown in insulation,,as long as it can't blow past and block the soffit.

r40 is much nicer in the attic to keep the heat out from radiating down.

Remember the past or all is lost.

Click to reply button
Inspiration banner


Post a reply as Anonymous

Photo must be in JPG, GIF or PNG format and less than 5MB.

Reply choose button


Post new button or Login button

To test the boundaries of small-footprint living, interior designer Jessica Helgerson moved her family to a 540-square-foo... Filling an underutilized area beneath the stairs is a smart way to save space. Doing so with a stash of wood, however, is ... The Audubon Society inspired wallpaper in this Adirondack-styled mudroom will get you in the outdoor mood. Grab your coat ... Chalkboard paint opens up endless possibilities for customizing your dresser time and time again. Use chalk to label the c... A fireplace in the bathroom creates the ultimate setting for relaxation. Homeowners often choose electric or gas over wood... This roomy boot tray made from punched metal stands up to all the elements. Station it in your mudroom or at your back doo... There’s nothing like a new set of cabinet hardware to refresh a room. The possibilities are endless: Go modern, rustic, or... FLOR tiles are an affordable way to customize a carpeted floor covering for any space. Make anything from runners to wall-... Chalkboard paint features prominently in this elegant yet unpretentious headboard design. Add a new message daily to reflec... Salvaged boards in varying widths and colors make up the dramatic accent wall in this attic space. The high-gloss white of... The indecisive homeowner need not fret over choosing one (or even two) cabinet colors. The kitchen cabinets in this artist... Incorporate nature into your lighting scheme by securing a dead tree in a concrete mold and draping your pendant lamp from... Simple and striking, a couple of pieces of "lovingly used" furniture creates a special kind of charm. A weathered chair fo... First dress up your metal shelves with a coat of paint in an accent color that complements your kitchen decor. Then arrang... Dark wood shelving and a matching upholstered bench keep this closet sleek and refined. The large window brightens the sub...
Follow banner a
Newsletter icon Flipboard glossy Facebook Twitter Pinterest Youtube Rss icon