Latest Discussions : Tools & Workshop

darryl1

04:43PM | 09/16/04
Member Since: 09/15/04
1 lifetime posts
Does anyone know how I can download an owners manual for an old Craftsman 10 in. radial arm saw--model no. 113.197751?

Thanks

bravey

10:47AM | 10/02/04
Member Since: 06/23/04
161 lifetime posts
Unlike most manufacturers S***s doesn't offer downloads of their manuals even though you've already bought it once. They do, however, offer to RE-SELL it and send it in the mail. Even H****r F*****t offers free downloads of their manuals. You can order a copy from s***s.com by following this thread:

s***s.com

"parts"

search model number "113.197751"

"continue"

search "manual"

click "non illustrated parts"

select "owners manual"

place order

Incidently, the part number fot the manual is 63784.

Good Luck

feather

03:25PM | 04/05/05
Member Since: 04/04/05
1 lifetime posts
The manual for this model is available by calling Customer Service at 1-800-325-1184.

There is also a recall on this saw due to a great number of serious injuries. A free guard, new table and hardware will be sent. Go to http://www.radialarmsawrecall.com/index2.htm You will need model number and serial number found on the front of the saw base. There is a manual to be found through a link on this page but is is to be used with the original manual.

If you need help with the installation, they will pay $100.00 to cover shipping expenses for the yoke assembly.

broho3

04:14PM | 05/16/05
Member Since: 05/15/05
1 lifetime posts
Have you gotten your manual yet? I have one and could copy it and mail it to your for the cost of postage or email you a pdf version.

johnkatkus

09:04AM | 08/18/05
Member Since: 08/17/05
5 lifetime posts
Good Morning - You Wrote -

May 16th, 2005 08:14 PMHave you gotten your manual yet? I have one and could copy it and mail it to your for the cost of postage or email you a pdf version.

My Reply - can you please send me the pdf version of this manual to john_katkus@sbcglobal.net? Do you need any contributions for your effort on this part? Please let me know.

Thanks for your help

John Katkus

Crystal Lake, IL 60014

ehoppe

05:40PM | 10/30/05
Member Since: 10/29/05
3 lifetime posts
After all these years, I finally wired my shop for 220. Now I can't find the manual for my 113.197751 to figure out how to change the wiring. If you could send the pdf to me as well, I would greatly appreciate it. Thanks!!

Please send to eric.hoppe@gmail.com.

---ehops

paul0424

05:36PM | 11/07/05
Member Since: 11/06/05
1 lifetime posts
If it wouldn't be to much trouble could you please send me a copy of the operators manual? I just bought a used 10 inch radial arm saw model 113.197751 and of course it didn't come with a manual. My email address is pcj0424@hotmail.com.

Thanks, Paul

oldhogger

06:25AM | 11/30/05
Member Since: 11/29/05
2 lifetime posts
Hi...I too bought an old Craftsman Radial 10" Saw without a manual. If anyone is copying the manual I would happily send $ for postage and paper. They were built to last, too bad Sears didn't make the booklet the same way.

Thanks for any help anyone can offer.

Fraser

Belle River, Ontario

N0R 1A0

oldhogger

11:54AM | 12/01/05
Member Since: 11/29/05
2 lifetime posts
I forgot to leave an address. Should anyone have the manual I would appreciate a copy of a copy. oldhogger@yahoo.com

Thanks again, Fraser

ehoppe

05:23PM | 12/03/05
Member Since: 10/29/05
3 lifetime posts
I decided to just start ripping things apart and doing the trial and error approach. Changing the wiring for 220 was a piece of cake. Truly, anyone could do it. The saw cuts with great vigor, now!!! We will try to keep the fingers out of the blade.

---ehops

woodworkingpop

12:17PM | 12/17/05
Member Since: 12/16/05
1 lifetime posts
I too purchased an old 10 inch radial arm

saw and would appreciate a copy of the manual. If anyone has it in pdf format please send it to woodworkingpop@hotmail.com.

Thanks in advance....

mdooley

05:04PM | 01/22/06
Member Since: 01/21/06
1 lifetime posts
Just picked up fathers Raidal Arm saw. Wired for 220. Need to rewire for 115. Any ideas.

Can I get a copy of that manual.

Thanks much


ehoppe

02:20PM | 01/23/06
Member Since: 10/29/05
3 lifetime posts
Simply remove the plastic cover on the motor housing. There is a VERY EASY wiring diagram showing which colors go to which connectors for 110 or 220.

Even someone with zero electrical experience should be able to complete this taask in about 10 minutes.

I would assume since you bought a radial arm saw, you know what you are doing and are pretty good with your hands. The radial arm is easily the most dangerous tool in your shop.

Good luck

---ehops

honeydewityourself

02:36AM | 02/07/06
Member Since: 02/06/06
2 lifetime posts
I am a babyboomer do it yourselfer and of all the tools I have used ..the one I need for my next job , I don't have a clue how to use and can't find the manual.. I really wanted to cut my new step treads today. May I have have a pdf copy of the owners manual you guys are passing around.?

Laura

honeydewityourself

02:38AM | 02/07/06
Member Since: 02/06/06
2 lifetime posts
I forgot to leave my email for the owners manual .. it is lauralkls@aol.com

thanks

Durham5

12:34PM | 02/22/06
Member Since: 02/21/06
1 lifetime posts
Could somebody be so kind as to send me the pdf file for the manual to rjf5@yahoo.com.

It would be greatly appreciated. Still haven't got a clue why they wouldn't have this info available for free.

Barney100

11:21AM | 03/04/06
Member Since: 03/03/06
1 lifetime posts
I too just bought a Radial Arm saw Model Number 113 29461 and could really use a owners manual. chiefbb@msn.com

forkliftfreddy

06:09PM | 03/11/06
Member Since: 03/10/06
2 lifetime posts
can I get a pdf of the owner's manual too

forkliftfreddy

06:11PM | 03/11/06
Member Since: 03/10/06
2 lifetime posts
sorry I did not put my email address in. it is oconnorf@twcny.rr.com

thank you

Fastfirstshooter

06:46AM | 03/13/06
Member Since: 03/12/06
1 lifetime posts
I have an owner's manual for the Craftsman 113.197751 radial arm saw. I will be happy to share a copy with anyone who wants a copy. U pay copy costs and postage.

FFS/JPM


chagnons

06:21PM | 04/05/06
Member Since: 04/04/06
2 lifetime posts
I bought an old craftsman 10" radial arm saw I don't know the model number but if you still have the pdf manual I would greatly appreciate if you could send me a copy.

shekou001@aol.com

MPBJRtrey

09:08AM | 04/19/06
Member Since: 04/18/06
1 lifetime posts
Good Morning - You Wrote -

May 16th, 2005 08:14 PMHave you gotten your manual yet? I have one and could copy it and mail it to your for the cost of postage or email you a pdf version.

If not to much trouble, could I also have a copy of the pdf version of this manual sent to mympbjr@cox.net?

Thanks for your help,

Mike Breen

Parma Hts. OH


Barlow59

04:27PM | 05/08/06
Member Since: 05/07/06
1 lifetime posts
I also woul like the pdf manual for the Sears Radial Arm Saw. I need to know if I need a 20 amp breaker for this.

chagnons

05:39PM | 05/08/06
Member Since: 04/04/06
2 lifetime posts
Model 113.23100 requires 11 amp.(120Volts) so you are OK with a 15 amp breaker. If you want this pdf manual I need your Email.

Farmdudde

08:48AM | 07/01/06
Member Since: 06/30/06
1 lifetime posts
Hello I have just inherited a 10" radial arm saw model 113.23100 and was wondering if I could get the manual you have available emailed to me.


doug seibert

12:11PM | 07/01/06
Member Since: 08/10/02
842 lifetime posts
FarmDude......This thread concerns a different model saw.......

OldWoodWorkingMachines has your correct manual published on it's website as a free PDF file.....

Use this link and scroll down to RadialArmSaws and find your model #.......

http://www.owwm.com/MfgIndex/Publications.asp?ID=222

"...measure once.....cut twice....throw that one away and cut a new one...."

Handy1

02:19AM | 07/14/06
Member Since: 07/10/06
2 lifetime posts
--I am so sorry to add to your growing list of request for this. Is there anything we can do to get the might and all knowing in power to see the good customer relations it brings in providing this information? Craftsman Sears of all companies, Ha! As they say it's not your Dads Company. What a shame. Well thank you.

Ciamthepink12@Hotmail.com

Woodmiser

09:30AM | 07/14/06
Member Since: 07/13/06
2 lifetime posts
Hi all, I bought a 10" Craftsman Radial Arm Saw, it has the lazer on it.

The saw head is all the way back to the colume end, it seems to be locked and I can't pull it forward, no matter what I try. Has it been pushed to far back, or is there a lock system that I'm missing...

Write me here, or at b138@hotmail if you can help...

Bob AKA Wooodmiser


Woodmiser

09:32AM | 07/14/06
Member Since: 07/13/06
2 lifetime posts
Hi, my Craftsman 10" Radial Arm Saw is locked, I can't pull it forward. It is all the way back towards the colume. I tried all the releases I see, is there something I'm missing? Could it be jamed somehow?

Any advise will help...

Bob

justice779

11:40AM | 07/23/06
Member Since: 07/22/06
2 lifetime posts
good afternoon, if you get the pdf version of the owners manual can you forward it to me, thanks, dave in ga.

justice779

11:42AM | 07/23/06
Member Since: 07/22/06
2 lifetime posts
forgot to include my e-mail adddress justice779@no.$pam.aol.com

Sven2389

11:05AM | 08/03/06
Member Since: 07/18/06
9 lifetime posts
there will be a latch or thumb screw on the sawmotor carriage assy, often on the right hand set of rollers - look for a thumbscrew or latch lever that binds the carriage to the rails.

RDovel

12:45PM | 08/12/06
Member Since: 08/11/06
3 lifetime posts
I have a Craftsman 10" radial saw. Model 113.197751. Could you please send a PDF file of the manual for this saw to my email? It is rdovel57@mchsi.com Thank you

pfflyer

05:10AM | 08/13/06
Member Since: 08/12/06
1 lifetime posts
I also bought a used one with no manual. If it is still available please e-mail it to p_fronek@yahoo.com

Thanks

RDovel

08:05AM | 08/14/06
Member Since: 08/11/06
3 lifetime posts
Could you send a copy by email, a PDF file, to my email address. rdovel57@mchsi.com

Let me know if you would like a donation. Thank you

Ray Dovel

RDovel

09:34AM | 08/15/06
Member Since: 08/11/06
3 lifetime posts
I just found out there is a serious recall on this saw. If you have one contact Sears on the web or at your local Sears store. You have to have the model number and serial number to check if your saw is one of the recalls. If your saw is on the recall list all necessary parts will be sent to you or your saw can be sent to the factory for repair.

olyjim

07:56PM | 09/07/06
Member Since: 09/06/06
1 lifetime posts
I am just another fool with this saw, but no manual...Sears wants $8 for it plus shipping...I have already given Sears plenty of money for parts to get this saw back in shape. I would sure appriciate the PDF if anyone has it...Once I recieve it I will upload it to a web address for all, and then noone should have to send it again.

Thanks for your help.

jamessorensen@comcast.net

123456abcdef

06:41PM | 09/22/06
Member Since: 09/21/06
1 lifetime posts
would like a copy of the radial arm saw 113.197751 users manual in pdf format.

is there a cost?

i am at bnutzman@hughes.net

thanks

bob


ghshaw

10:24AM | 09/25/06
Member Since: 09/22/06
2 lifetime posts
If you still have a PDF copy of this manual, could you please send it to me at shaw.gh@gmail.com? I would certainly appreciate it.

cornham1

06:51PM | 10/14/06
Member Since: 10/13/06
1 lifetime posts
I could also use the pdf of the Craftsman Radial Arm Saw manual, model 113.197751. E-mail address is: cornham1@yahoo.com. Thank you.

sprint67

04:20PM | 10/16/06
Member Since: 10/15/06
1 lifetime posts
If anyone out there still has that pdf I would also like a copy too. I can also host it on the net and post a link so others can just download it in the future.

thanks

sprint 67 at hotmail dot com

ripcord

11:19AM | 10/22/06
Member Since: 10/21/06
2 lifetime posts
does anyone have any information on a recall of this model.a new fence,table and hardware due to many injuries.

thanks

Billhart

01:59PM | 10/22/06
Member Since: 04/25/05
1915 lifetime posts
You can check the model here.

http://www.radialarmsawrecall.com/index2.asp


shellylynn

12:58PM | 11/10/06
Member Since: 11/09/06
1 lifetime posts
I really need to rewire the connections for the motor 113.63607 for radial arm saw 113.197751. I did the safety retrofit for the saw blade guard. Very sorry I lost the manual.

I want a way to download the rewiring instructions.

willyg65

12:49PM | 11/27/06
Member Since: 11/26/06
2 lifetime posts
would you send me the pdf of the 113.197751 manual. my e-mail address is:

wmartineac172060MI@comcast.net

This would be greatly appreciated.

Bill Martineac

Romulus,MI


patmiller20

06:24PM | 01/03/07
Member Since: 01/02/07
1 lifetime posts
Could you please email me a pdf copy of the Craftsman radial arm saw? My email is mrmillervhs@yahoo.com

sailorjim

10:51AM | 03/06/07
Member Since: 03/05/07
1 lifetime posts
Could you please email a copy, pdf format, of the owners manual for the radial arm saw. I just bought a 10 craftsman and it does not have the owners manual. Please email to:

sailorjim@earthlink.net

Thank you for your trouble. Jim

bertsrun

07:08AM | 03/16/07
Member Since: 03/15/07
1 lifetime posts
Could you please email a copy, pdf format, of the owners manual for the radial arm saw. I just bought a used 10 inch 113.197751 Craftsman and it does not have the owner's manual. Please email to:

bertsrun@infionline.net.

Thank you for your trouble. Bill

JoeInGA

06:54AM | 03/18/07
Member Since: 03/17/07
1 lifetime posts
If I could get a pdf of the manual I would really appreciate it. Thanks!

e-mail is joe.multiworks@gmail.com

oilytailpipe

10:30AM | 05/10/07
Member Since: 05/09/07
7 lifetime posts
Could you please email a copy, pdf format, of the owners manual for the radial arm saw. Craftsman 10 inch 113.197751. I do not have the owner's manual. Please email to: oilytailpipe@hotmail.com

thanks

mason1974

11:52AM | 06/14/07
Member Since: 06/13/07
2 lifetime posts
i need a copy if anyone has one can you email me dashrzor_x@hotmail.com

thanks

mason

oilytailpipe

01:25PM | 06/14/07
Member Since: 05/09/07
7 lifetime posts
Mason,

I tried to emailing the manual to you, but I got a failure to deliver.

Is this email address correct?

dashrzor_x@hotmail.com

Walt,

oilytailpipe@hotmail.com

mason1974

04:43AM | 06/16/07
Member Since: 06/13/07
2 lifetime posts
my adress is dashrazor_x@hotmail.com

i need a manual for a 113.19771

thanks

mason

xpress1833

05:19AM | 06/29/07
Member Since: 06/28/07
1 lifetime posts
I too just came across a Craftsman RAS 113.197751 and need to find a copy of the manual. If anyone has a pdf. version I would greatly appreciate a copy. Please email to xpress1833@yahoo.com. Thanks

dgav97

07:32PM | 07/06/07
Member Since: 07/05/07
1 lifetime posts
Just bought a used Craftsman Radial Arm #113.197751. If anyone has a .pdf version of the manual to share I would appreciate it.

dgav97@yahoo.com

jeniferrobert

04:32AM | 07/08/07
Member Since: 07/06/07
8 lifetime posts
Hi, just wanted to know if you recieved a copy of or an email for 113.19771 for I need one also if you wouldn't mind sending me a copy I would appreciate it. you can send it email pfd file or how ever I just need one thnks.

jeniferrobert@bellsouth.net

ghshaw

04:55AM | 07/08/07
Member Since: 09/22/06
2 lifetime posts
I know I have a paper copy, and will check for an ecopy when I return from vacation. At worst I can scan in the paper one and send it to you. send me your email address to shaw.gh@gmail.com. Thanks. I will do it later in the week.

jeniferrobert

05:16AM | 07/08/07
Member Since: 07/06/07
8 lifetime posts
thank-you so much . enjoy your vacation!

jeniferrobert

05:23AM | 07/08/07
Member Since: 07/06/07
8 lifetime posts
Hi new here just want to know if you recieved your munual i'm looking for the same one if so could you send it to me. thanks

jeniferrobert@bellsouth.net

woodvendor

12:27PM | 07/09/07
Member Since: 07/08/07
2 lifetime posts
After reving the cover and wiring to the switch I took my motor to the local small engine repair man. The instructions are UNDER THE COVER! He just switched two wires to different teminals. It tells you what goes where. Took less than 5 minutes.

jeniferrobert

05:04PM | 07/18/07
Member Since: 07/06/07
8 lifetime posts
This manual is much needed not only by me but many on this site is ther a way it can be posted on the site so they can click on it and down load it from here. how simple. I have gotten my recall Items but still need the owners manual 113.19771 or 113 1997751 i'll take either one Thanks you can post or email me with the pdf file.

Jenifer

jeniferrobert@bellsouth.net

vicjenk

05:19AM | 07/23/07
Member Since: 07/22/07
1 lifetime posts
I could use one of these manuals sent to me pdf or other format by e-mail thanks in advance. please send to vicjenk@hotmail.com

jeniferrobert

06:25AM | 07/31/07
Member Since: 07/06/07
8 lifetime posts
Just ask owwm.com to post my pdf manual that I sumitted don''t know how long it takes but the manual is 44 pages and in full saw there was a great need for it thats at the owwm.com under craftsman Radial arm saws

Hope this helps youall Jenifer

ToolUser

06:11PM | 08/05/07
Member Since: 08/04/07
2 lifetime posts
I am attempting to assemble a mobile base for a 113.199250 and I'd like to get it right. Two wheels have breaks (?) and two do not. Which corners do these go on? Anyone have assy instructions?

Thanks!

doug seibert

06:46PM | 08/05/07
Member Since: 08/10/02
842 lifetime posts
Old Wood Working Machines has the PDF manual for the #199200 (and with a base # 199250)

Check the site.....scroll down to RAS #199200......The manual shows the standard legs....NO casters

The casters fit standard holes in the legs.....usually they allow the user to select their location.......I suspect you'll want the front two wheels to lock for easy access as you approach/move the RAS.......

http://www.owwm.com/MfgIndex/Publications.asp?ID=222

"...measure once.....cut twice....throw that one away and cut a new one...."

rosharo

12:48PM | 08/23/07
Member Since: 08/22/07
2 lifetime posts
Saw an old post where broho3 had a sears manual he could email as PDF.

That would be great if anyone can do that or tell me where I can get it.

Had mine since 1993. Need to know how to do an alignment.

Thanks,

Ross

doug seibert

04:42PM | 08/23/07
Member Since: 08/10/02
842 lifetime posts
A BobVilaPoster.....Jenifer....has recently posted the manual at OWWM.....THANKS Jenifer !

Use this LINK...Scroll down to Radial Arm Saws and locate your Model......""NEW""

http://www.owwm.com/MfgIndex/Publications.asp?ID=222.asp?ID=222

After selecting the manual .....You'll need to click the link once.....and then click the Link once again on the PayPal/Adobe page....(the download is Free, but of course they'll accept a donation)

Also you may also want to download the 133 page "Radial Arm Saw.....Wood, Plastic and Metalworking Know-How" circa 1969.....It has lots of woodworking info as well as alignment proceedures......table and fence building.......Jigs......

"...measure once.....cut twice....throw that one away and cut a new one...."

rosharo

06:09PM | 08/24/07
Member Since: 08/22/07
2 lifetime posts
Thanks Doug....I guess. Email said you had a reply but I can't even find my original post...the last 2/3 days.

Didn't find my model, 113.196120 on OWWM but maybe 113.197751 is close ehough or the same thing.

Thanks,

Ross

dplatz

04:47PM | 10/17/07
Member Since: 10/16/07
3 lifetime posts
do you remember what the recall was repairing? a couple of years ago I got the updated blade guard as a recall. The motor on my saw just died. Sears doesn't have a replacement unit but sells all the parts. I am not an electrician so I am stuck at the moment.

oilytailpipe

08:28PM | 10/17/07
Member Since: 05/09/07
7 lifetime posts
The recall was for an improved Blade Guard Assembly, it shields the blade more for your safety. You also get a complete new Table Top with the kit.

The saw was manufactured by Emerson Tool Co. They may be able help you with the motor.

Here is a link to the recall webpage: http://www.radialarmsawrecall.com/

Here is a webpage on a start up problem: http://wiki.answers.com/Q/How_to_fix_Craftsman_radial_arm_saw_starting_problem

I had a problem where it didn't want to start. I would take a good size screwdriver by the bit and would rap the motor with the handle. It would start. After having to use this procedure for 10 15 times to start the saw it did not act up again.

good luck,

Walt

dplatz

03:43PM | 10/18/07
Member Since: 10/16/07
3 lifetime posts
I saw the recall notice in a Sears store and did get the new guard and table top. that was an added bonus. I will look up emerson tool and see if I can get a new motor. Sears has all the parts but not a complete motor. Again, Thanks.

dplatz

05:29PM | 10/18/07
Member Since: 10/16/07
3 lifetime posts
After researching more and speaking with my Elec. Eng. brother both seem to think it is the Motor Start Capacitor. I have ordered a new one from Sears and will reply back if that fixes the motor. I found a good article here on repairing this model.

http://www.ridgidforum.com/forum/archive/index.php/t-9888.html

good suggestions and tips on repairing this saw.

Brianj51

05:50AM | 10/23/07
Member Since: 10/22/07
1 lifetime posts
since we are on the subject of owners manuals, does anyone have the operating(owners) manual for a Sears Craftsman Radial arm saw model number #113.197150?

Please contact me : brianjosephlowe@comcast.net

Thanks in advance,

Brian

dxlync07

08:51AM | 12/01/07
Member Since: 11/30/07
1 lifetime posts
I also need a pdf copy of the manual for this radial arm saw (113.197751). If you can email a copy to my email address at "donlynch@isp.com" I will appreciate it.

k63wilson

11:50AM | 12/11/07
Member Since: 12/10/07
1 lifetime posts
Hello Friends-

I just inherited a 113.199250 from a grandparent and would love to start using it... but I cannot find a manual for it.

If anyone has a copy of one (PDF version or mail (I pay postage, of course)) I would greatly appreciate it.

Thanks Very Much

nyfd269

03:54AM | 12/12/07
Member Since: 12/10/07
3 lifetime posts
I just purchased a used Electronic Radial Arm Saw model #113.198210 and of course, there was no user manual. Does anyone have a manual that they could send to me via e-mail in a PDF File for this model or a similar model; hopefully the instructions will be similar.

I'm also can not bevel the motor head. I unlock the bevel lever but the head doesn't move, any suggestions?

Thanks.

nyfd@adelphia.net

hoodhome

05:43PM | 12/26/07
Member Since: 12/25/07
1 lifetime posts
COULD YOU PLEASE TELL ME IF YOU'VE GOT ANY INFORMATION ON HOW I MAY OBTAIN AN OWNER'S MANUAL FOR THIS MODEL?

oilytailpipe

06:01PM | 12/26/07
Member Since: 05/09/07
7 lifetime posts
E-mail oilytailpipe@hotmail.com and I can e-mail you a RADIAL ARM SAW # 113.197751 MANUAL i pdf format.

Walt

bandit1

08:14AM | 12/28/07
Member Since: 12/27/07
1 lifetime posts
I too am looking for a manual on the radial arm saw 113 278 641 c. If any one has one could they email to me

patonj@elkvalley.net

johnkatkus

03:11PM | 01/01/08
Member Since: 08/17/05
5 lifetime posts
This is the information that I have found for the Craftsman 10 inch radial arm saw. My model number is 113.197751. This manual looks similar to the one that I had when I purchased my Craftsman many years ago. I found this by using google.com and searching for the Craftsman 10 inch radial saw recall. Hope this helps.

John Katkus

Crystal Lake, IL

http://www.radialarmsawrecall.com/pub/sp6039-3.pdf

johnkatkus

03:12PM | 01/01/08
Member Since: 08/17/05
5 lifetime posts
This is the information that I have found for the Craftsman 10 inch radial arm saw. My model number is 113.197751. This manual looks similar to the one that I had when I purchased my Craftsman many years ago. I found this by using google.com and searching for the Craftsman 10 inch radial saw recall. Hope this helps.

John Katkus

Crystal Lake, IL

http://www.radialarmsawrecall.com/pub/sp6039-3.pdf

johnkatkus

03:13PM | 01/01/08
Member Since: 08/17/05
5 lifetime posts
This is the information that I have found for the Craftsman 10 inch radial arm saw. My model number is 113.197751. This manual looks similar to the one that I had when I purchased my Craftsman many years ago. I found this by using google.com and searching for the Craftsman 10 inch radial saw recall. Hope this helps.

John Katkus

Crystal Lake, IL

http://www.radialarmsawrecall.com/pub/sp6039-3.pdf

johnkatkus

03:14PM | 01/01/08
Member Since: 08/17/05
5 lifetime posts
This is the information that I have found for the Craftsman 10 inch radial arm saw. My model number is 113.197751. This manual looks similar to the one that I had when I purchased my Craftsman many years ago. I found this by using google.com and searching for the Craftsman 10 inch radial saw recall. Hope this helps.

John Katkus

Crystal Lake, IL

http://www.radialarmsawrecall.com/pub/sp6039-3.pdf

nyfd269

07:15PM | 01/01/08
Member Since: 12/10/07
3 lifetime posts
John,

Thanks for your reply. I received this manual from Emerson Tools when they sent me the recall kit, but it's only for the Guard Kit, not the owners manual. I have an electronic model and the electronic angle display screen doesn't work even after I replaced the battery. The only angles I am sure of are the 90 & 45, all other will be guesses as their is no manual angle adjustments on this saw.

John

xmarine

03:48PM | 03/20/08
Member Since: 03/19/08
1 lifetime posts
I also need an owners manual for a craftman saw # 113.197751.Any chance of sending me the PDF?Just bought the saw today and don't know about all the levers and adjustments.Thanks Tim Fagan. vette99@centurytel.net

Handyman1954

11:20AM | 05/03/08
Member Since: 05/02/08
2 lifetime posts
I downloaded the exact manual for that model by going to www.managemyhome.com

where registration is free and quick and their search engine is easy to use. The files are in pdf format so you'll need free adobe acrobat reader. Let me know if you were successful.

oilytailpipe

12:32PM | 05/03/08
Member Since: 05/09/07
7 lifetime posts
Handyman1954

I have these manuals in pdf format for the following Craftsman models:

113.19760

113.22010

113.29411

113.197110

113.197150

113.197751

113.199200

113.299040

If you want any e-mail me at oilytailpipe@hotmail.com

Walt

Indyboo

06:19PM | 05/07/08
Member Since: 05/06/08
2 lifetime posts
I was given an old Craftsman 10" Radial Arm Saw but it does not have the stand with it, just the saw and the mounting frame with a homemade plywood table. How can I figure out what the model# is without the stand so I can find a manual? It looks like it might be quite a bit older than the models mentioned in this thread. Also does anyone know where I can get a stand and adjustable table for it?

dmpieper

07:41AM | 07/11/08
Member Since: 07/10/08
1 lifetime posts
Can anyone provide where I can find the manual that comes with the recall installation kit in pdf, easier to get on line? I ordered this kit but have misplaced the manual which tells you how to install everything.

Thanks

Del Pieper

craftswoman

07:10AM | 09/08/08
Member Since: 09/07/08
1 lifetime posts
this is probably getting repeditave and old but could you also send me a copy of the manual for 113.19771 please

charly142006@msn.com

iskowitzsa

04:51PM | 09/16/08
Member Since: 09/15/08
1 lifetime posts
Came across this site while looking for a manual for Lawn mower I just purchased and was surprised to see the comments that Sears ie Craftsman does not have manuals available unless you pay for them.

I found a Sears parts site that if you put in the model it will pull up information on the item and on the right hand site of the web page it shows a link to a manual if available. You folks might want to check out this link

http://www.searspartsdirect.com/partsdirect/index.action

rthornton

03:37PM | 09/26/08
Member Since: 09/25/08
1 lifetime posts
I also would like a pdf file if it isn' to mutch trouble rthornton@neo.rr.com

raelibark98

08:00AM | 12/27/08
Member Since: 12/26/08
1 lifetime posts
could one of you please send me a pdf copy of the radial arm saw manual as well?

chris.thompson@rbfc.org

thanks so much

wajones

06:13PM | 02/08/09
Member Since: 02/07/09
1 lifetime posts
I just purchased a Craftsman 10" Radial Arm Saw today for $70. It needs a bit of cleaning up, but seems to work well. While looking for a user manual, I found this site along with the below info. I hope this helps.

You can get a pdf copy of the user manual here. http://www.owwm.com/mfgindex/pubdetail.aspx?id=2238

FYI: There is a recall on the Craftsman saws having a model number starting with 113.

You can find that info here.

http://www.radialarmsawrecall.com/

Schlich10

07:45PM | 02/09/09
Member Since: 02/05/09
3 lifetime posts
Could you tell me where the other wires connect.

triker59

09:12AM | 03/25/09
Member Since: 03/24/09
2 lifetime posts
i forgot to leave an email- trikester59@gmail.com

david munro

radialarmsawmanual

12:09PM | 04/19/09
Member Since: 04/18/09
1 lifetime posts
apparently the Craftsman Radial Arm Saws are/were made by a company called emerson tool company and are the subject of a recall for a defective blade guard - check out the link below and down load the manual and save a couple of bucks since sears still charging for the manual

http://www.radialarmsawrecall.com/pub/sp6039-3.pdf

doug seibert

04:13PM | 04/19/09
Member Since: 08/10/02
842 lifetime posts
Nice try BUT......That's the manual for the replacement BLADE GUARD.....NOT for the saw......it has the generic "saw" manual without exploded views and parts breakdown......

Original manuals can usually be found by registering and searching at "Manage My Home"

http://www.managemyhome.com/mmh/products/ManualSearchDisplay.action

OR

Searching at OldWoodWorkingMachines:

http://www.owwm.com/mfgindex/detail.aspx?id=222&tab=3

"......measure Once.....cut Twice....

throw that one away and cut a new one...."

johnhughes

09:26AM | 08/22/09
Member Since: 08/21/09
1 lifetime posts
I got a copy of 1 of the saw manuals. I got it from a link on the Sears parts website. My saw is pre 1977 so it is not a recall. Check the DOM. Enter your part number and if they have it woolah. If you don't know your number try this one, 113.23100.

kloppy

02:48PM | 09/14/09
Member Since: 09/13/09
2 lifetime posts
I found the Craftsman Manual for the Radial Saw 113.197751 http://www.hammerwall.com/Manuals/Craftsman/Description/113.197751/Craftsman%2010%20Inch%20Radial%20Saw/L0711116/

Handyman1954

04:22AM | 09/15/09
Member Since: 05/02/08
2 lifetime posts
Please go to www.managemyhome.com and on the manuals tab enter your model number for your owner's manual 113.197751

Handyman

06:17AM | 09/15/09
Member Since: 11/18/98
187 lifetime posts
Here is a link directly to the manual for 113.197751.

Owners Manual here

vincejean

06:44AM | 10/05/09
Member Since: 10/04/09
1 lifetime posts
If you still have the .pdf of the manual, could you email me a copy also

vj3biro@gmail.com

thanks

Vince


Post a reply as Anonymous

Photo must be in JPG, GIF or PNG format and less than 5MB.

Reply choose button

Anonymous

Post new button or Login button
Register