07:13PM | 09/12/02
Member Since: 09/11/02
78 lifetime posts
I have two separate lighting fixtures I want to install in my basement that should both be connected to the same on/off switch.

1. For a power source, can I wire the fixtures to an existing junction box that is already wired to the circuit breaker?

2. Can I wire one fixture to the other, and that one to a junction box already wired to the circuit breaker?

3. Double checking--to turn both fixtures on simultaneously on the same switch, I run a wire from each fixture to the switch, connect them, and connect the joined wiring to the switch terminals?

Whew! I appreciate any help!



11:30PM | 09/12/02
Member Since: 09/03/02
3 lifetime posts
My first advice is always to call a qualified electrician. If you insist on DIY then here is the best I can tell you with the info provided. I cannot insure that I'm providing the knowledge that is gained from a 4 year apprenticeship progam. I don't mean to sound
antagonistic, but only try to convey the gravity of your safety and the importance of proper electrical installation. Although a small project I can no way cover here all the required elements.

Question 1 answer is maybe.
Depending on
The ampacity rating of the existing
circuit, the existing load on the circuit,
the wattage of the new fixtures,
and the number of wires in the existing box.

Question 2 answer is yes with the same concerns given for question 1

Question 3 Clarify
You run the wire from each fixture to the switch "BOX" in the the box they are connected via wirenut to a pigtail and the pigtail is connected to the lower terminal
of the switch. The hot is connected to the upper terminal. Again provided you don't exceed conductor fill in the box. You can also daisy chain from fixture to fixture
either using a J-box @ the fixtures or fixtures approved for such.

This is all taking into account you understand all the other requirements of doing the installation. IE
Size of boxes, size of wire, type of wire,type of fittings,
strapping requirements, box sizing requirements, length of wire in boxes, amount of insulation to strip, correct wire nuts to use and how to properly put them on, routing requirements for cable under floor joist, grounding requirements, wire color for switch leg, etc etc etc etc

If you do know all then proceed, if not keep reading your wiring book. It's always a good idea to get a permit and inspection. If you are a novice in wiring but want to DIY it's a good idea to have someone qualified take a look at your work before you enegize. And remember to turn off the breaker and check with a tester before making your final terminations.

Good Luck

[This message has been edited by TE (edited September 13, 2002).]

Bill Addiss

06:31AM | 09/13/02
Member Since: 09/12/02
9 lifetime posts

Please understand that sometimes (ok, often) it is difficult for people to give safe and accurate advice based on a description alone. The answer to what you are asking can vary greatly depending on your situation. We cannot see these junction boxes or what they contain. It could be a simple procedure, but then again ...

If you are determined to try this yourself I strongly suggest that you first find a good book on basic wiring procedures. There are some excellent books available that should help you get the answers to these questions. One that comes to mind is called "Wiring Simplified" and it has been around for many years and is constantly revised to keep up with current codes. It is widely available and very reasonably priced. It has been a great help to many for a long time.

Good Luck, and be safe,

Click to reply button
Inspiration banner


Post a reply as Anonymous

Photo must be in JPG, GIF or PNG format and less than 5MB.

Reply choose button


Post new button or Login button

To test the boundaries of small-footprint living, interior designer Jessica Helgerson moved her family to a 540-square-foo... Filling an underutilized area beneath the stairs is a smart way to save space. Doing so with a stash of wood, however, is ... The Audubon Society inspired wallpaper in this Adirondack-styled mudroom will get you in the outdoor mood. Grab your coat ... Chalkboard paint opens up endless possibilities for customizing your dresser time and time again. Use chalk to label the c... A fireplace in the bathroom creates the ultimate setting for relaxation. Homeowners often choose electric or gas over wood... This roomy boot tray made from punched metal stands up to all the elements. Station it in your mudroom or at your back doo... There’s nothing like a new set of cabinet hardware to refresh a room. The possibilities are endless: Go modern, rustic, or... FLOR tiles are an affordable way to customize a carpeted floor covering for any space. Make anything from runners to wall-... Chalkboard paint features prominently in this elegant yet unpretentious headboard design. Add a new message daily to reflec... Salvaged boards in varying widths and colors make up the dramatic accent wall in this attic space. The high-gloss white of... The indecisive homeowner need not fret over choosing one (or even two) cabinet colors. The kitchen cabinets in this artist... Incorporate nature into your lighting scheme by securing a dead tree in a concrete mold and draping your pendant lamp from... Simple and striking, a couple of pieces of "lovingly used" furniture creates a special kind of charm. A weathered chair fo... First dress up your metal shelves with a coat of paint in an accent color that complements your kitchen decor. Then arrang... Dark wood shelving and a matching upholstered bench keep this closet sleek and refined. The large window brightens the sub...
Follow banner a
Newsletter icon Flipboard glossy Facebook Twitter Pinterest Youtube Rss icon