I'm going to make an octagon around a round column using crown moulding and want to know how to determine the angle to use on the mitre box. Let's just say for this example the column is 12" round.
I can somewhat figure out that it is probably half of a 45degree angle used for 90degree inside/outside mitres on 90degree walls, and making the same angled mitred cuts on both ends should get me the results i'm looking for.
Q#2: If it was previously done and one section needed to be replaced how are the mitres degrees,angles determined for the piece being replaced.
Is their a tool that will give me the angle?
360 degrees in a circle divided by 8 for your octagon is a 45 degree angle divided by 2 for your mitre cut is 22.5" on your saw. doesn't matter if its a 2" circle or a 22" circle. you just need to determine the length of your parts. I suggest drawing it out on paper first so your not cutting up your wood figuring it out
http://www.woodcentral.com/bparticles/bpindex2.shtml#downloads
....Compound Miter or the Polygon.......
....Compound Miter or the Polygon.......
A common problem for first timers is laying the crown molding flat on its back when making the cut. This requires a compound angle saw and multiple angles.
Lay the crown molding against the saw fence at the same angle as it sets on the wall (or column). Clamp a strip of wood to the table to maintain that angle. When working with crown molding you must pretend that the saw fence is the wall and the table is the ceiling. The 22.5 degree cut is made without tilting the blade.
Regards
Lay the crown molding against the saw fence at the same angle as it sets on the wall (or column). Clamp a strip of wood to the table to maintain that angle. When working with crown molding you must pretend that the saw fence is the wall and the table is the ceiling. The 22.5 degree cut is made without tilting the blade.
Regards
Thanks, yea some years ago i did cut a crown mould a few times before i figured out how to place in in the box, then it was EZ..lol
Thanks for the help.
Thanks for the help.
Roofus,
You'll find a full tutorial on my site for installing crown.
Plus charts, a crown angle calculator, flat & in position step by step photos, all free.
The direct link is:
http://www.altereagle.com/How_to_install.htm
...any further questions use the dedicated crown molding forum onsite.
http://www.altereagle.com/
http://decks-ca.com
http://kingofcrown.com
Alter Eagle Construction & Design
You'll find a full tutorial on my site for installing crown.
Plus charts, a crown angle calculator, flat & in position step by step photos, all free.
The direct link is:
http://www.altereagle.com/How_to_install.htm
...any further questions use the dedicated crown molding forum onsite.
http://www.altereagle.com/
http://decks-ca.com
http://kingofcrown.com
Alter Eagle Construction & Design
Post a reply as Anonymous
Related Discussions
EXTERIOR of NEW Windows Fogging up and creating Thousands of Droplets of Condensation
This spring we had all of our windows replaced. The last two times that it has rained we found that ALL of our Windows fogged up on ...
6
answers
1 day by BV019788
Miter Cut
I am building a childern's play house and am having probles with the angle of the roof where two roofs meet. Both roofs are 45-degr...
5
answersabout 16 years by Altereagle
Plumbing
I put in a new shower where an old tub once was. I put a p trap under drain for shower and ran pvc to old drain. I did not dig it ou...
2
answers7 days by BV019748
Giant weeds are killing us!
Hello everyone, Starting about 7 years ago we had this strange giant 10 foot weed show up in our yard. We pulled it up and though...
2
answers1 day by BV019792
